MySmartHome/MySensors
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Ethernet SoftSPI

Browse Source 
Update ethernet sketch to give correct instructions when using
W5100/SoftSPI.
This commit is contained in:
Henrik Ekblad
2014-11-14 00:36:49 +01:00
parent 4783cac945
commit 024d6efb82
1 changed files with 14 additions and 23 deletions
Download Patch File Download Diff File Expand all files Collapse all files
libraries/MySensors/examples/EthernetGateway/EthernetGateway.ino
+14 -23
View File
@@ -14,15 +14,17 @@
* *
* The GW code is designed for Arduino 328p / 16MHz. ATmega168 does not have enough memory to run this program. * The GW code is designed for Arduino 328p / 16MHz. ATmega168 does not have enough memory to run this program.
* *
* COMPILING ENC28J60 *
* COMPILING WIZNET (W5100) ETHERNET MODULE
* > Edit RF24_config.h in (libraries\MySensors\utility) to enable softspi (remove // before "#define SOFTSPI").
*
* COMPILING ENC28J60 ETHERNET MODULE
* > Use Arduino IDE 1.5.7 (or later) * > Use Arduino IDE 1.5.7 (or later)
* > Disable DEBUG in Sensor.h before compiling this sketch. Othervise the sketch will probably not fit in program space when downloading. * > Disable DEBUG in Sensor.h before compiling this sketch. Othervise the sketch will probably not fit in program space when downloading.
* > Remove Ethernet.h include below and inlcude UIPEthernet.h * > Remove Ethernet.h include below and include UIPEthernet.h
* COMPILING WizNET (W5100) * > Remove DigitalIO include
* > Remove UIPEthernet include below and include Ethernet.h. * Note that I had to disable UDP and DHCP support in uipethernet-conf.h to reduce space. (which means you have to choose a static IP for that module)
* *
* Note that I had to disable UDP and DHCP support in uipethernet-conf.h to reduce space. (which meas you ave to choose a static IP for that module)
* VERA CONFIGURATION: * VERA CONFIGURATION:
* Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin. * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin.
* E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003 * E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003
@@ -32,32 +34,21 @@
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
* ----------- Connection guide --------------------------------------------------------------------------- * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
* 13 Radio & Ethernet SPI SCK *
* 12 Radio & Ethernet SPI MISO (SO)
* 11 Radio & Ethernet SPI MOSI (SI)
* 10 Ethernet SPI Slave Select (CS) Pin 10, the SS pin, must be an o/p to put SPI in master mode
* 9 Radio TX LED using on board LED (optional) +5V -> LED -> 270-330 Ohm resistor -> pin 9.
* 8 Radio RX LED (optional) +5V -> LED -> 270-330 Ohm resistor -> pin 8.
* 7 Radio error LED (optional) +5V -> LED -> 270-330 Ohm resistor -> pin 7.
* 6 Radio SPI Slave Select
* 5 Radio Chip Enable
* 3 Inclusion mode button (optional), 10K pull down to GND, button to VCC)
* 2 Radio IRQ pin (optional), W5100 Int, if linked to pin 2)
* -----------------------------------------------------------------------------------------------------------
* Powering: both NRF24l01 radio and Ethernet(ENC28J60) uses 3.3V
*/ */
#include <DigitalIO.h> // This include can be removed when using UIPEthernet module
#include <SPI.h> #include <SPI.h>
#include <MySensor.h> #include <MySensor.h>
#include <MyGateway.h> #include <MyGateway.h>
#include <stdarg.h> #include <stdarg.h>
// Use this if you have attached a Ethernet ENC28J60 shields // Use this if you have attached a Ethernet ENC28J60 shields
#include <UIPEthernet.h> //#include <UIPEthernet.h>
// Use this fo WizNET module and Arduino Ethernet Shield // Use this fo WizNET W5100 module and Arduino Ethernet Shield
//#include <Ethernet.h> #include <Ethernet.h>
#define INCLUSION_MODE_TIME 1 // Number of minutes inclusion mode is enabled #define INCLUSION_MODE_TIME 1 // Number of minutes inclusion mode is enabled