Fixes LED issues as discussed in #562

Removing MY_LED_BLINKING_FEATURE, as we now are
using MY_DEFAULT_LED_xx_PIN defines to enable
LED blinking feature.

updated Gateway sketches to not refer to
MY_LED_BLINKING_FEATURE any more

fixes #562

examples/SensebenderGatewaySerial/SensebenderGatewaySerial.ino

@@ -19,33 +19,33 @@
  *******************************
  *
  * DESCRIPTION
- * The ArduinoGateway prints data received from sensors on the serial link. 
+ * The ArduinoGateway prints data received from sensors on the serial link.
  * The gateway accepts input on seral which will be sent out on radio network.
  *
  * This GW code is designed for Sensebender GateWay / Arduino Zero
  *
  * Wire connections (OPTIONAL):
- * - Inclusion button should be connected between digital pin 3 and GND  
+ * - Inclusion button should be connected between digital pin 3 and GND
  * - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
  *
  * LEDs (OPTIONAL):
- * - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h
+ * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
  * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
  * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
- * - ERR (red) - fast blink on error during transmission error or recieve crc error 
- * 
+ * - ERR (red) - fast blink on error during transmission error or recieve crc error
+ *
  */
 
 #define SKETCH_VERSION "0.1"
 // Enable debug prints to serial monitor
-#define MY_DEBUG 
+#define MY_DEBUG
 
 // Enable and select radio type attached
 #define MY_RADIO_NRF24
 //#define MY_RADIO_RFM69
 
 // Set LOW transmit power level as default, if you have an amplified NRF-module and
-// power your radio separately with a good regulator you can turn up PA level. 
+// power your radio separately with a good regulator you can turn up PA level.
 #define MY_RF24_PA_LEVEL RF24_PA_HIGH
 
 // Enable serial gateway
@@ -56,14 +56,6 @@
 #define MY_BAUD_RATE 38400
 #endif
 
-// Flash leds on rx/tx/err
-#define MY_LEDS_BLINKING_FEATURE
-// Set blinking period
-#define MY_DEFAULT_LED_BLINK_PERIOD 300
-
-// Inverses the behavior of leds
-//#define MY_WITH_LEDS_BLINKING_INVERSE
-
 // Enable inclusion mode
 #define MY_INCLUSION_MODE_FEATURE
 // Enable Inclusion mode button on gateway
@@ -73,10 +65,17 @@
 //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
 
 // Set inclusion mode duration (in seconds)
-#define MY_INCLUSION_MODE_DURATION 60 
+#define MY_INCLUSION_MODE_DURATION 60
 // Digital pin used for inclusion mode button
-//#define MY_INCLUSION_MODE_BUTTON_PIN  3 
+//#define MY_INCLUSION_MODE_BUTTON_PIN  3
 
+// Set blinking period
+#define MY_DEFAULT_LED_BLINK_PERIOD 300
+
+// Inverses the behavior of leds
+//#define MY_WITH_LEDS_BLINKING_INVERSE
+
+// Flash leds on rx/tx/err
 // Uncomment to override default HW configurations
 //#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
 //#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
@@ -93,16 +92,16 @@ Sd2Card card;
 static uint8_t num_of_leds = 5;
 static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};
 
-void setup() { 
+void setup() {
   // Setup locally attached sensors
 }
 
 void presentation() {
- // Present locally attached sensors 
+ // Present locally attached sensors
 }
 
-void loop() { 
-  // Send locally attached sensor data here 
+void loop() {
+  // Send locally attached sensor data here
 }
 
 
@@ -142,7 +141,7 @@ void preHwInit() {
     digitalWrite(LED_YELLOW, HIGH);
     tests++;
   }
-  
+
   if (testEEProm()) {
     digitalWrite(LED_ORANGE, HIGH);
     tests++;
@@ -155,7 +154,7 @@ void preHwInit() {
         digitalWrite(leds[i], LOW);
       }
     }
-  } 
+  }
   else {
     while (1) {
       digitalWrite(LED_RED, HIGH);
@@ -164,7 +163,7 @@ void preHwInit() {
       delay(200);
     }
   }
-  
+
 }
 
 bool testSha204(){
@@ -243,7 +242,7 @@ bool testEEProm() {
   delay(500);
   eeprom_d2 = i2c_eeprom_read_byte(EEPROM_VERIFICATION_ADDRESS);
   if (eeprom_d1 == eeprom_d2) {
-    SerialUSB.println("PASSED");    
+    SerialUSB.println("PASSED");
     i2c_eeprom_write_byte(EEPROM_VERIFICATION_ADDRESS, ~eeprom_d1);
     return true;
   }