MySmartHome/MySensors
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Fixes LED issues as discussed in #562

Browse Source 
Removing MY_LED_BLINKING_FEATURE, as we now are
using MY_DEFAULT_LED_xx_PIN defines to enable
LED blinking feature.

updated Gateway sketches to not refer to
MY_LED_BLINKING_FEATURE any more

fixes #562
This commit is contained in:
Thomas Mørch
2016-08-20 09:35:49 +02:00
parent c925dd6f5e
commit 15b46f8023
15 changed files with 216 additions and 276 deletions
Download Patch File Download Diff File Expand all files Collapse all files
MyConfig.h
+12 -15
View File
@@ -223,25 +223,22 @@
/********************************** /**********************************
* Information LEDs blinking * Information LEDs blinking
***********************************/ ***********************************/
// This feature enables LEDs blinking on message receive, transmit // If one of the following is defined here, or in the sketch, the pin will be used for the
// or if some error occurred. This was commonly used only in gateways, // corresponding led function.
// but now can be used in any sensor node. Also the LEDs can now be // They have to be enabled here (or in your sketch). Replace x with the pin number you have the LED on.
// disabled in the gateway. //
// NOTE!! that on some platforms (for example sensebender GW) the hardware variant can enable LEDs by default,
// These defaults can be overridden by defining one of these.
//#define MY_DEFAULT_ERR_LED_PIN x
//#define MY_DEFAULT_TX_LED_PIN x
//#define MY_DEFAULT_RX_LED_PIN x
//#define MY_LEDS_BLINKING_FEATURE // The following setting allows you to inverse the LED blinking
// The following setting allows you to inverse the blinking feature MY_LEDS_BLINKING_FEATURE
// When MY_WITH_LEDS_BLINKING_INVERSE is enabled LEDSs are normally turned on and switches // When MY_WITH_LEDS_BLINKING_INVERSE is enabled LEDSs are normally turned on and switches
// off when blinking // off when blinking
//#define MY_WITH_LEDS_BLINKING_INVERSE //#define MY_WITH_LEDS_BLINKING_INVERSE
// The following defines can be used to set the port pin, that the LED is connected to
// If one of the following is defined here, or in the sketch, MY_LEDS_BLINKING_FEATURE will be
// enabled by default. (Replace x with the pin number you have the LED on)
//#define MY_DEFAULT_ERR_LED_PIN x
//#define MY_DEFAULT_TX_LED_PIN x
//#define MY_DEFAULT_RX_LED_PIN x
/********************************************** /**********************************************
* Gateway inclusion button/mode configuration * Gateway inclusion button/mode configuration
@@ -431,7 +428,7 @@
/** /**
* @def MY_RX_MESSAGE_BUFFER_FEATURE * @def MY_RX_MESSAGE_BUFFER_FEATURE
* @brief This enabled the receiving buffer feature. * @brief This enabled the receiving buffer feature.
* *
* This feature is currently not supported for RFM69 and RS485, for RF24 MY_RF24_IRQ_PIN has to be defined. * This feature is currently not supported for RFM69 and RS485, for RF24 MY_RF24_IRQ_PIN has to be defined.
*/ */
@@ -439,7 +436,7 @@
/** /**
* @def MY_RX_MESSAGE_BUFFER_SIZE * @def MY_RX_MESSAGE_BUFFER_SIZE
* @brief Declare the amount of incoming messages that can be buffered. * @brief Declare the amount of incoming messages that can be buffered.
*/ */
#ifdef MY_RX_MESSAGE_BUFFER_FEATURE #ifdef MY_RX_MESSAGE_BUFFER_FEATURE
#ifndef MY_RX_MESSAGE_BUFFER_SIZE #ifndef MY_RX_MESSAGE_BUFFER_SIZE
MySensors.h
+4 -44
View File
@@ -84,17 +84,10 @@
#define MY_DEFAULT_RX_LED_PIN MY_HW_TX_LED_PIN #define MY_DEFAULT_RX_LED_PIN MY_HW_TX_LED_PIN
#endif #endif
// Not necessary to include blinking feature if no LED's are defined! #if defined(MY_LEDS_BLINKING_FEATURE)
#if defined(MY_LEDS_BLINKING_FEATURE) && !defined(MY_DEFAULT_RX_LED_PIN) && !defined(MY_DEFAULT_TX_LED_PIN) && !defined(MY_ERR_LED_PIN) #warning MY_LEDS_BLINKING_FEATURE is not working, define MY_DEFAULT_ERR_LED_PIN, MY_DEFAULT_TX_LED_PIN or MY_DEFAULT_RX_LED_PIN in your sketch
#undef MY_LEDS_BLINKING_FEATURE
#endif #endif
// Enable LED BLINKING FEATURE, if there are any LEDs defined.
#if defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_ERR_LED) || defined(MY_DEFAULT_TX_LED_PIN)
#define MY_LEDS_BLINKING_FEATURE
#endif
/** /**
* @def MY_DEFAULT_LED_BLINK_PERIOD * @def MY_DEFAULT_LED_BLINK_PERIOD
* @brief Default LEDs blinking period in milliseconds. * @brief Default LEDs blinking period in milliseconds.
@@ -102,41 +95,8 @@
#ifndef MY_DEFAULT_LED_BLINK_PERIOD #ifndef MY_DEFAULT_LED_BLINK_PERIOD
#define MY_DEFAULT_LED_BLINK_PERIOD 300 #define MY_DEFAULT_LED_BLINK_PERIOD 300
#endif #endif
/**
* @def MY_DEFAULT_RX_LED_PIN
* @brief The RX LED default pin.
*/
#ifndef MY_DEFAULT_RX_LED_PIN
#if defined(ARDUINO_ARCH_ESP8266)
#define MY_DEFAULT_RX_LED_PIN 8
#else
#define MY_DEFAULT_RX_LED_PIN 6
#endif
#endif
/**
* @def MY_DEFAULT_TX_LED_PIN
* @brief The TX LED default pin.
*/
#ifndef MY_DEFAULT_TX_LED_PIN
#if defined(ARDUINO_ARCH_ESP8266)
#define MY_DEFAULT_TX_LED_PIN 9
#else
#define MY_DEFAULT_TX_LED_PIN 5
#endif
#endif
/**
* @def MY_DEFAULT_ERR_LED_PIN
* @brief The Error LED default pin.
*/
#ifndef MY_DEFAULT_ERR_LED_PIN
#if defined(ARDUINO_ARCH_ESP8266)
#define MY_DEFAULT_ERR_LED_PIN 7
#else
#define MY_DEFAULT_ERR_LED_PIN 4
#endif
#endif
#if defined(MY_LEDS_BLINKING_FEATURE) #if defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_TX_LED_PIN) || defined(MY_DEFAULT_ERR_LED_PIN)
#include "core/MyLeds.cpp" #include "core/MyLeds.cpp"
#else #else
#include "core/MyLeds.h" #include "core/MyLeds.h"
@@ -270,7 +230,7 @@
#endif #endif
#if defined(MY_PARENT_NODE_IS_STATIC) && (MY_PARENT_NODE_ID == AUTO) #if defined(MY_PARENT_NODE_IS_STATIC) && (MY_PARENT_NODE_ID == AUTO)
#error Parent is static but no parent ID defined. #error Parent is static but no parent ID defined.
#endif #endif
// Make sure to disable child features when parent feature is disabled // Make sure to disable child features when parent feature is disabled
core/MyIndication.cpp
+10 -4
View File
@@ -18,20 +18,26 @@
*/ */
#include "MyIndication.h" #include "MyIndication.h"
#ifdef MY_LEDS_BLINKING_FEATURE #if defined(MY_DEFAULT_TX_LED_PIN)|| defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_ERR_LED_PIN)
#include "MyLeds.h" #include "MyLeds.h"
#endif #endif
void setIndication( const indication_t ind ) void setIndication( const indication_t ind )
{ {
#ifdef MY_LEDS_BLINKING_FEATURE #if defined(MY_DEFAULT_TX_LED_PIN)
if ((INDICATION_TX == ind) || (INDICATION_GW_TX == ind)) if ((INDICATION_TX == ind) || (INDICATION_GW_TX == ind))
{ {
ledsBlinkTx(1); ledsBlinkTx(1);
} else if ((INDICATION_RX == ind) || (INDICATION_GW_RX == ind)) } else
#endif
#if defined(MY_DEFAULT_RX_LED_PIN)
if ((INDICATION_RX == ind) || (INDICATION_GW_RX == ind))
{ {
ledsBlinkRx(1); ledsBlinkRx(1);
} else if (ind > INDICATION_ERR_START) } else
#endif
#if defined(MY_DEFAULT_ERR_LED_PIN)
if (ind > INDICATION_ERR_START)
{ {
// Number of blinks indicates which error occurred. // Number of blinks indicates which error occurred.
ledsBlinkErr(ind-INDICATION_ERR_START); ledsBlinkErr(ind-INDICATION_ERR_START);
core/MyLeds.cpp
+12 -2
View File
@@ -37,10 +37,15 @@ inline void ledsInit()
countErr = 0; countErr = 0;
// Setup led pins // Setup led pins
#if defined(MY_DEFAULT_RX_LED_PIN)
pinMode(MY_DEFAULT_RX_LED_PIN, OUTPUT); pinMode(MY_DEFAULT_RX_LED_PIN, OUTPUT);
#endif
#if defined(MY_DEFAULT_TX_LED_PIN)
pinMode(MY_DEFAULT_TX_LED_PIN, OUTPUT); pinMode(MY_DEFAULT_TX_LED_PIN, OUTPUT);
#endif
#if defined(MY_DEFAULT_ERR_LED_PIN)
pinMode(MY_DEFAULT_ERR_LED_PIN, OUTPUT); pinMode(MY_DEFAULT_ERR_LED_PIN, OUTPUT);
#endif
ledsProcess(); ledsProcess();
} }
@@ -55,17 +60,23 @@ void ledsProcess() {
// For an On/Off ratio of 4, the pattern repeated will be [on, on, on, off] // For an On/Off ratio of 4, the pattern repeated will be [on, on, on, off]
// until the counter becomes 0. // until the counter becomes 0.
#if defined(MY_DEFAULT_RX_LED_PIN)
state = (countRx & (LED_ON_OFF_RATIO-1)) ? LED_ON : LED_OFF; state = (countRx & (LED_ON_OFF_RATIO-1)) ? LED_ON : LED_OFF;
hwDigitalWrite(MY_DEFAULT_RX_LED_PIN, state); hwDigitalWrite(MY_DEFAULT_RX_LED_PIN, state);
if (countRx) --countRx; if (countRx) --countRx;
#endif
#if defined(MY_DEFAULT_TX_LED_PIN)
state = (countTx & (LED_ON_OFF_RATIO-1)) ? LED_ON : LED_OFF; state = (countTx & (LED_ON_OFF_RATIO-1)) ? LED_ON : LED_OFF;
hwDigitalWrite(MY_DEFAULT_TX_LED_PIN, state); hwDigitalWrite(MY_DEFAULT_TX_LED_PIN, state);
if (countTx) --countTx; if (countTx) --countTx;
#endif
#if defined(MY_DEFAULT_ERR_LED_PIN)
state = (countErr & (LED_ON_OFF_RATIO-1)) ? LED_ON : LED_OFF; state = (countErr & (LED_ON_OFF_RATIO-1)) ? LED_ON : LED_OFF;
hwDigitalWrite(MY_DEFAULT_ERR_LED_PIN, state); hwDigitalWrite(MY_DEFAULT_ERR_LED_PIN, state);
if (countErr) --countErr; if (countErr) --countErr;
#endif
} }
void ledsBlinkRx(uint8_t cnt) { void ledsBlinkRx(uint8_t cnt) {
@@ -79,4 +90,3 @@ void ledsBlinkTx(uint8_t cnt) {
void ledsBlinkErr(uint8_t cnt) { void ledsBlinkErr(uint8_t cnt) {
if(!countErr) { countErr = cnt*LED_ON_OFF_RATIO; } if(!countErr) { countErr = cnt*LED_ON_OFF_RATIO; }
} }
core/MyLeds.h
+1 -1
View File
@@ -29,7 +29,7 @@
#define LED_OFF 0x1 #define LED_OFF 0x1
#endif #endif
#ifdef MY_LEDS_BLINKING_FEATURE #if defined(MY_DEFAULT_TX_LED_PIN) || defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_ERR_LED_PIN)
#define ledBlinkTx(x,...) ledsBlinkTx(x) #define ledBlinkTx(x,...) ledsBlinkTx(x)
#define ledBlinkRx(x,...) ledsBlinkRx(x) #define ledBlinkRx(x,...) ledsBlinkRx(x)
#define ledBlinkErr(x,...) ledsBlinkErr(x) #define ledBlinkErr(x,...) ledsBlinkErr(x)
core/MySensorsCore.cpp
+3 -3
View File
@@ -35,7 +35,7 @@ void (*_timeCallback)(unsigned long); // Callback for requested time messages
void _process() { void _process() {
hwWatchdogReset(); hwWatchdogReset();
#if defined (MY_LEDS_BLINKING_FEATURE) #if defined (MY_DEFAULT_TX_LED_PIN) || defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_ERR_LED_PIN)
ledsProcess(); ledsProcess();
#endif #endif
@@ -58,7 +58,7 @@ void _infiniteLoop() {
#if defined(ARDUINO_ARCH_ESP8266) #if defined(ARDUINO_ARCH_ESP8266)
yield(); yield();
#endif #endif
#if defined (MY_LEDS_BLINKING_FEATURE) #if defined (MY_DEFAULT_TX_LED_PIN) || defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_ERR_LED_PIN)
ledsProcess(); ledsProcess();
#endif #endif
} }
@@ -81,7 +81,7 @@ void _begin() {
before(); before();
} }
#if defined(MY_LEDS_BLINKING_FEATURE) #if defined(MY_DEFAULT_TX_LED_PIN) || defined(MY_DEFAULT_RX_LED_PIN) || defined(MY_DEFAULT_ERR_LED_PIN)
ledsInit(); ledsInit();
#endif #endif
examples/GatewayESP8266/GatewayESP8266.ino
+22 -26
View File
@@ -20,34 +20,34 @@
* *
* REVISION HISTORY * REVISION HISTORY
* Version 1.0 - Henrik EKblad * Version 1.0 - Henrik EKblad
* Contribution by a-lurker and Anticimex, * Contribution by a-lurker and Anticimex,
* Contribution by Norbert Truchsess <norbert.truchsess@t-online.de> * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
* Contribution by Ivo Pullens (ESP8266 support) * Contribution by Ivo Pullens (ESP8266 support)
* *
* DESCRIPTION * DESCRIPTION
* The EthernetGateway sends data received from sensors to the WiFi link. * The EthernetGateway sends data received from sensors to the WiFi link.
* The gateway also accepts input on ethernet interface, which is then sent out to the radio network. * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
* *
* VERA CONFIGURATION: * VERA CONFIGURATION:
* Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin. * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin.
* E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003 * E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003
* *
* LED purposes: * LED purposes:
* - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch, only the LEDs that is defined is used.
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
* See http://www.mysensors.org/build/esp8266_gateway for wiring instructions. * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
* nRF24L01+ ESP8266 * nRF24L01+ ESP8266
* VCC VCC * VCC VCC
* CE GPIO4 * CE GPIO4
* CSN/CS GPIO15 * CSN/CS GPIO15
* SCK GPIO14 * SCK GPIO14
* MISO GPIO12 * MISO GPIO12
* MOSI GPIO13 * MOSI GPIO13
* GND GND * GND GND
* *
* Not all ESP8266 modules have all pins available on their external interface. * Not all ESP8266 modules have all pins available on their external interface.
* This code has been tested on an ESP-12 module. * This code has been tested on an ESP-12 module.
* The ESP8266 requires a certain pin configuration to download code, and another one to run code: * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
@@ -56,10 +56,10 @@
* - Connect CH_PD via 10K resistor to VCC * - Connect CH_PD via 10K resistor to VCC
* - Connect GPIO2 via 10K resistor to VCC * - Connect GPIO2 via 10K resistor to VCC
* - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch') * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
* *
* Inclusion mode button: * Inclusion mode button:
* - Connect GPIO5 via switch to GND ('inclusion switch') * - Connect GPIO5 via switch to GND ('inclusion switch')
* *
* Hardware SHA204 signing is currently not supported! * Hardware SHA204 signing is currently not supported!
* *
* Make sure to fill in your ssid and WiFi password below for ssid & pass. * Make sure to fill in your ssid and WiFi password below for ssid & pass.
@@ -67,7 +67,7 @@
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 9600 #define MY_BAUD_RATE 9600
@@ -95,14 +95,14 @@
#define MY_IP_GATEWAY_ADDRESS 192,168,178,1 #define MY_IP_GATEWAY_ADDRESS 192,168,178,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0 #define MY_IP_SUBNET_ADDRESS 255,255,255,0
// The port to keep open on node server mode // The port to keep open on node server mode
#define MY_PORT 5003 #define MY_PORT 5003
// How many clients should be able to connect to this gateway (default 1) // How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2 #define MY_GATEWAY_MAX_CLIENTS 2
// Controller ip address. Enables client mode (default is "server" mode). // Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
// Enable inclusion mode // Enable inclusion mode
@@ -111,16 +111,15 @@
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
// #define MY_INCLUSION_BUTTON_FEATURE // #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3 #define MY_INCLUSION_MODE_BUTTON_PIN 3
// Flash leds on rx/tx/err
// #define MY_LEDS_BLINKING_FEATURE
// Set blinking period // Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300 // #define MY_DEFAULT_LED_BLINK_PERIOD 300
// Flash leds on rx/tx/err
// Led pins used if blinking feature is enabled above // Led pins used if blinking feature is enabled above
#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin #define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin #define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
@@ -134,17 +133,14 @@
#include <MySensors.h> #include <MySensors.h>
void setup() { void setup() {
} }
void presentation() { void presentation() {
// Present locally attached sensors here // Present locally attached sensors here
} }
void loop() { void loop() {
// Send locally attached sensors data here // Send locally attached sensors data here
} }
examples/GatewayESP8266MQTTClient/GatewayESP8266MQTTClient.ino
+21 -25
View File
@@ -20,26 +20,26 @@
* *
* REVISION HISTORY * REVISION HISTORY
* Version 1.0 - Henrik Ekblad * Version 1.0 - Henrik Ekblad
* *
* DESCRIPTION * DESCRIPTION
* The ESP8266 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker. * The ESP8266 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker.
* The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network * The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network
* *
* LED purposes: * LED purposes:
* - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs in your sketch
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
* See http://www.mysensors.org/build/esp8266_gateway for wiring instructions. * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
* nRF24L01+ ESP8266 * nRF24L01+ ESP8266
* VCC VCC * VCC VCC
* CE GPIO4 * CE GPIO4
* CSN/CS GPIO15 * CSN/CS GPIO15
* SCK GPIO14 * SCK GPIO14
* MISO GPIO12 * MISO GPIO12
* MOSI GPIO13 * MOSI GPIO13
* *
* Not all ESP8266 modules have all pins available on their external interface. * Not all ESP8266 modules have all pins available on their external interface.
* This code has been tested on an ESP-12 module. * This code has been tested on an ESP-12 module.
* The ESP8266 requires a certain pin configuration to download code, and another one to run code: * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
@@ -48,10 +48,10 @@
* - Connect CH_PD via 10K resistor to VCC * - Connect CH_PD via 10K resistor to VCC
* - Connect GPIO2 via 10K resistor to VCC * - Connect GPIO2 via 10K resistor to VCC
* - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch') * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
* *
* Inclusion mode button: * Inclusion mode button:
* - Connect GPIO5 via switch to GND ('inclusion switch') * - Connect GPIO5 via switch to GND ('inclusion switch')
* *
* Hardware SHA204 signing is currently not supported! * Hardware SHA204 signing is currently not supported!
* *
* Make sure to fill in your ssid and WiFi password below for ssid & pass. * Make sure to fill in your ssid and WiFi password below for ssid & pass.
@@ -59,7 +59,7 @@
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 9600 #define MY_BAUD_RATE 9600
@@ -87,7 +87,7 @@
#define MY_ESP8266_PASSWORD "MyVerySecretPassword" #define MY_ESP8266_PASSWORD "MyVerySecretPassword"
// Set the hostname for the WiFi Client. This is the hostname // Set the hostname for the WiFi Client. This is the hostname
// it will pass to the DHCP server if not static. // it will pass to the DHCP server if not static.
// #define MY_ESP8266_HOSTNAME "mqtt-sensor-gateway" // #define MY_ESP8266_HOSTNAME "mqtt-sensor-gateway"
// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP) // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
@@ -98,27 +98,26 @@
#define MY_IP_SUBNET_ADDRESS 255,255,255,0 #define MY_IP_SUBNET_ADDRESS 255,255,255,0
// MQTT broker ip address. // MQTT broker ip address.
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
// The MQTT broker port to to open // The MQTT broker port to to open
#define MY_PORT 1883 #define MY_PORT 1883
/* /*
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Enable inclusion mode // Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3 #define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Flash leds on rx/tx/err
#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin #define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin #define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED #define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED
@@ -127,17 +126,14 @@
#include <ESP8266WiFi.h> #include <ESP8266WiFi.h>
#include <MySensors.h> #include <MySensors.h>
void setup() { void setup() {
} }
void presentation() { void presentation() {
// Present locally attached sensors here // Present locally attached sensors here
} }
void loop() { void loop() {
// Send locally attech sensors data here // Send locally attech sensors data here
} }
examples/GatewayESP8266OTA/GatewayESP8266OTA.ino
+22 -27
View File
@@ -21,34 +21,34 @@
* REVISION HISTORY * REVISION HISTORY
* Version 1.0 - Henrik EKblad * Version 1.0 - Henrik EKblad
* Contribution by tekka, * Contribution by tekka,
* Contribution by a-lurker and Anticimex, * Contribution by a-lurker and Anticimex,
* Contribution by Norbert Truchsess <norbert.truchsess@t-online.de> * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
* Contribution by Ivo Pullens (ESP8266 support) * Contribution by Ivo Pullens (ESP8266 support)
* *
* DESCRIPTION * DESCRIPTION
* The EthernetGateway sends data received from sensors to the WiFi link. * The EthernetGateway sends data received from sensors to the WiFi link.
* The gateway also accepts input on ethernet interface, which is then sent out to the radio network. * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
* *
* VERA CONFIGURATION: * VERA CONFIGURATION:
* Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin. * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin.
* E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003 * E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003
* *
* LED purposes: * LED purposes:
* - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
* See http://www.mysensors.org/build/esp8266_gateway for wiring instructions. * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
* nRF24L01+ ESP8266 * nRF24L01+ ESP8266
* VCC VCC * VCC VCC
* CE GPIO4 * CE GPIO4
* CSN/CS GPIO15 * CSN/CS GPIO15
* SCK GPIO14 * SCK GPIO14
* MISO GPIO12 * MISO GPIO12
* MOSI GPIO13 * MOSI GPIO13
* GND GND * GND GND
* *
* Not all ESP8266 modules have all pins available on their external interface. * Not all ESP8266 modules have all pins available on their external interface.
* This code has been tested on an ESP-12 module. * This code has been tested on an ESP-12 module.
* The ESP8266 requires a certain pin configuration to download code, and another one to run code: * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
@@ -57,10 +57,10 @@
* - Connect CH_PD via 10K resistor to VCC * - Connect CH_PD via 10K resistor to VCC
* - Connect GPIO2 via 10K resistor to VCC * - Connect GPIO2 via 10K resistor to VCC
* - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch') * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
* *
* Inclusion mode button: * Inclusion mode button:
* - Connect GPIO5 via switch to GND ('inclusion switch') * - Connect GPIO5 via switch to GND ('inclusion switch')
* *
* Hardware SHA204 signing is currently not supported! * Hardware SHA204 signing is currently not supported!
* *
* Make sure to fill in your ssid and WiFi password below for ssid & pass. * Make sure to fill in your ssid and WiFi password below for ssid & pass.
@@ -69,7 +69,7 @@
#include <ArduinoOTA.h> #include <ArduinoOTA.h>
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h // Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
#define MY_BAUD_RATE 9600 #define MY_BAUD_RATE 9600
@@ -97,14 +97,14 @@
#define MY_IP_GATEWAY_ADDRESS 192,168,178,1 #define MY_IP_GATEWAY_ADDRESS 192,168,178,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0 #define MY_IP_SUBNET_ADDRESS 255,255,255,0
// The port to keep open on node server mode // The port to keep open on node server mode
#define MY_PORT 5003 #define MY_PORT 5003
// How many clients should be able to connect to this gateway (default 1) // How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 2 #define MY_GATEWAY_MAX_CLIENTS 2
// Controller ip address. Enables client mode (default is "server" mode). // Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. // Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
// Enable inclusion mode // Enable inclusion mode
@@ -113,16 +113,15 @@
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
// #define MY_INCLUSION_BUTTON_FEATURE // #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3 #define MY_INCLUSION_MODE_BUTTON_PIN 3
// Flash leds on rx/tx/err
// #define MY_LEDS_BLINKING_FEATURE
// Set blinking period // Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300 // #define MY_DEFAULT_LED_BLINK_PERIOD 300
// Flash leds on rx/tx/err
// Led pins used if blinking feature is enabled above // Led pins used if blinking feature is enabled above
#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin #define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin #define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
@@ -136,8 +135,8 @@
#include <MySensors.h> #include <MySensors.h>
void setup() { void setup() {
ArduinoOTA.onStart([]() { ArduinoOTA.onStart([]() {
Serial.println("ArduinoOTA start"); Serial.println("ArduinoOTA start");
}); });
@@ -163,7 +162,7 @@ void setup() {
} }
void presentation() { void presentation() {
// Present locally attached sensors here // Present locally attached sensors here
} }
@@ -171,7 +170,3 @@ void loop() {
// Send locally attech sensors data here // Send locally attech sensors data here
ArduinoOTA.handle(); ArduinoOTA.handle();
} }
examples/GatewaySerial/GatewaySerial.ino
+21 -27
View File
@@ -19,25 +19,25 @@
******************************* *******************************
* *
* DESCRIPTION * DESCRIPTION
* The ArduinoGateway prints data received from sensors on the serial link. * The ArduinoGateway prints data received from sensors on the serial link.
* The gateway accepts input on seral which will be sent out on radio network. * The gateway accepts input on seral which will be sent out on radio network.
* *
* The GW code is designed for Arduino Nano 328p / 16MHz * The GW code is designed for Arduino Nano 328p / 16MHz
* *
* Wire connections (OPTIONAL): * Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND * - Inclusion button should be connected between digital pin 3 and GND
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series * - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
* *
* LEDs (OPTIONAL): * LEDs (OPTIONAL):
* - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
*/ */
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Enable and select radio type attached // Enable and select radio type attached
@@ -45,7 +45,7 @@
//#define MY_RADIO_RFM69 //#define MY_RADIO_RFM69
// Set LOW transmit power level as default, if you have an amplified NRF-module and // Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level. // power your radio separately with a good regulator you can turn up PA level.
#define MY_RF24_PA_LEVEL RF24_PA_LOW #define MY_RF24_PA_LEVEL RF24_PA_LOW
// Enable serial gateway // Enable serial gateway
@@ -56,14 +56,6 @@
#define MY_BAUD_RATE 38400 #define MY_BAUD_RATE 38400
#endif #endif
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE
// Enable inclusion mode // Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
@@ -73,30 +65,32 @@
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3 //#define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE
// Flash leds on rx/tx/err
// Uncomment to override default HW configurations // Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin //#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin //#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN 5 // the PCB, on board LED //#define MY_DEFAULT_TX_LED_PIN 5 // the PCB, on board LED
#include <MySensors.h> #include <MySensors.h>
void setup() { void setup() {
// Setup locally attached sensors // Setup locally attached sensors
} }
void presentation() { void presentation() {
// Present locally attached sensors // Present locally attached sensors
} }
void loop() { void loop() {
// Send locally attached sensor data here // Send locally attached sensor data here
} }
examples/GatewaySerialRS485/GatewaySerialRS485.ino
+20 -26
View File
@@ -19,23 +19,22 @@
******************************* *******************************
* *
* DESCRIPTION * DESCRIPTION
* The RS485 Gateway prints data received from sensors on the serial link. * The RS485 Gateway prints data received from sensors on the serial link.
* The gateway accepts input on seral which will be sent out on * The gateway accepts input on seral which will be sent out on
* the RS485 link. * the RS485 link.
* *
* Wire connections (OPTIONAL): * Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND * - Inclusion button should be connected between digital pin 3 and GND
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series * - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
* *
* LEDs (OPTIONAL): * LEDs (OPTIONAL):
* - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
* The gateway uses AltSoftSerial to handle two serial links * The gateway uses AltSoftSerial to handle two serial links
* on one Arduino. Use the following pins for RS485 link * on one Arduino. Use the following pins for RS485 link
* *
* Board Transmit Receive PWM Unusable * Board Transmit Receive PWM Unusable
* ----- -------- ------- ------------ * ----- -------- ------- ------------
* Teensy 3.0 & 3.1 21 20 22 * Teensy 3.0 & 3.1 21 20 22
@@ -46,16 +45,16 @@
* Arduino Mega 46 48 44, 45 * Arduino Mega 46 48 44, 45
* Wiring-S 5 6 4 * Wiring-S 5 6 4
* Sanguino 13 14 12 * Sanguino 13 14 12
* *
*/ */
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Enable RS485 transport layer // Enable RS485 transport layer
#define MY_RS485 #define MY_RS485
// Define this to enables DE-pin management on defined pin // Define this to enables DE-pin management on defined pin
#define MY_RS485_DE_PIN 2 #define MY_RS485_DE_PIN 2
// Set RS485 baud rate to use // Set RS485 baud rate to use
@@ -64,39 +63,34 @@
// Enable serial gateway // Enable serial gateway
#define MY_GATEWAY_SERIAL #define MY_GATEWAY_SERIAL
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Enable inclusion mode // Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
#define MY_INCLUSION_BUTTON_FEATURE #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
#define MY_INCLUSION_MODE_BUTTON_PIN 3 #define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Flash leds on rx/tx/err
#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin #define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
#define MY_DEFAULT_RX_LED_PIN 5 // Receive led pin #define MY_DEFAULT_RX_LED_PIN 5 // Receive led pin
#define MY_DEFAULT_TX_LED_PIN 6 // the PCB, on board LED #define MY_DEFAULT_TX_LED_PIN 6 // the PCB, on board LED
#include <MySensors.h> #include <MySensors.h>
void setup() { void setup() {
// Setup locally attached sensors // Setup locally attached sensors
} }
void presentation() { void presentation() {
// Present locally attached sensors // Present locally attached sensors
} }
void loop() { void loop() {
// Send locally attached sensor data here // Send locally attached sensor data here
} }
examples/GatewayW5100/GatewayW5100.ino
+19 -21
View File
@@ -42,68 +42,67 @@
*/ */
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Enable and select radio type attached // Enable and select radio type attached
#define MY_RADIO_NRF24 #define MY_RADIO_NRF24
//#define MY_RADIO_RFM69 //#define MY_RADIO_RFM69
// Enable gateway ethernet module type // Enable gateway ethernet module type
#define MY_GATEWAY_W5100 #define MY_GATEWAY_W5100
// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal) // W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4 //#define MY_W5100_SPI_EN 4
// Enable Soft SPI for NRF radio (note different radio wiring is required) // Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with // The W5100 ethernet module seems to have a hard time co-operate with
// radio on the same spi bus. // radio on the same spi bus.
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD) #if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
#define MY_SOFTSPI #define MY_SOFTSPI
#define MY_SOFT_SPI_SCK_PIN 14 #define MY_SOFT_SPI_SCK_PIN 14
#define MY_SOFT_SPI_MISO_PIN 16 #define MY_SOFT_SPI_MISO_PIN 16
#define MY_SOFT_SPI_MOSI_PIN 15 #define MY_SOFT_SPI_MOSI_PIN 15
#endif #endif
// When W5100 is connected we have to move CE/CSN pins for NRF radio // When W5100 is connected we have to move CE/CSN pins for NRF radio
#ifndef MY_RF24_CE_PIN #ifndef MY_RF24_CE_PIN
#define MY_RF24_CE_PIN 5 #define MY_RF24_CE_PIN 5
#endif #endif
#ifndef MY_RF24_CS_PIN #ifndef MY_RF24_CS_PIN
#define MY_RF24_CS_PIN 6 #define MY_RF24_CS_PIN 6
#endif #endif
// Enable to UDP // Enable to UDP
//#define MY_USE_UDP //#define MY_USE_UDP
#define MY_IP_ADDRESS 192,168,178,66 // If this is disabled, DHCP is used to retrieve address #define MY_IP_ADDRESS 192,168,178,66 // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP // Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000 //#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode // The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003 #define MY_PORT 5003
// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254
// Controller ip address. Enables client mode (default is "server" mode).
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254
// The MAC address can be anything you want but should be unique on your network. // The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use. // Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use "DEAD BEEF FEED" for the MAC address. // Note that most of the Ardunio examples use "DEAD BEEF FEED" for the MAC address.
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Enable inclusion mode // Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE //#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3 //#define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Flash leds on rx/tx/err
// Uncomment to override default HW configurations // Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 7 // Error led pin //#define MY_DEFAULT_ERR_LED_PIN 7 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 8 // Receive led pin //#define MY_DEFAULT_RX_LED_PIN 8 // Receive led pin
@@ -123,4 +122,3 @@ void setup()
void loop() { void loop() {
} }
examples/GatewayW5100MQTTClient/GatewayW5100MQTTClient.ino
+24 -28
View File
@@ -20,7 +20,7 @@
* *
* REVISION HISTORY * REVISION HISTORY
* Version 1.0 - Henrik Ekblad * Version 1.0 - Henrik Ekblad
* *
* DESCRIPTION * DESCRIPTION
* The W5100 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker. * The W5100 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker.
* The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network * The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network
@@ -29,17 +29,17 @@
* - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
* See http://www.mysensors.org/build/esp8266_gateway for wiring instructions. * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
* nRF24L01+ ESP8266 * nRF24L01+ ESP8266
* VCC VCC * VCC VCC
* CE GPIO4 * CE GPIO4
* CSN/CS GPIO15 * CSN/CS GPIO15
* SCK GPIO14 * SCK GPIO14
* MISO GPIO12 * MISO GPIO12
* MOSI GPIO13 * MOSI GPIO13
* *
* Not all ESP8266 modules have all pins available on their external interface. * Not all ESP8266 modules have all pins available on their external interface.
* This code has been tested on an ESP-12 module. * This code has been tested on an ESP-12 module.
* The ESP8266 requires a certain pin configuration to download code, and another one to run code: * The ESP8266 requires a certain pin configuration to download code, and another one to run code:
@@ -48,10 +48,10 @@
* - Connect CH_PD via 10K resistor to VCC * - Connect CH_PD via 10K resistor to VCC
* - Connect GPIO2 via 10K resistor to VCC * - Connect GPIO2 via 10K resistor to VCC
* - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch') * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
* *
* Inclusion mode button: * Inclusion mode button:
* - Connect GPIO5 via switch to GND ('inclusion switch') * - Connect GPIO5 via switch to GND ('inclusion switch')
* *
* Hardware SHA204 signing is currently not supported! * Hardware SHA204 signing is currently not supported!
* *
* Make sure to fill in your ssid and WiFi password below for ssid & pass. * Make sure to fill in your ssid and WiFi password below for ssid & pass.
@@ -59,7 +59,7 @@
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Enables and select radio type (if attached) // Enables and select radio type (if attached)
#define MY_RADIO_NRF24 #define MY_RADIO_NRF24
@@ -75,23 +75,23 @@
#define MY_MQTT_CLIENT_ID "mysensors-1" #define MY_MQTT_CLIENT_ID "mysensors-1"
// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal) // W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4 //#define MY_W5100_SPI_EN 4
// Enable Soft SPI for NRF radio (note different radio wiring is required) // Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with // The W5100 ethernet module seems to have a hard time co-operate with
// radio on the same spi bus. // radio on the same spi bus.
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD) #if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
#define MY_SOFTSPI #define MY_SOFTSPI
#define MY_SOFT_SPI_SCK_PIN 14 #define MY_SOFT_SPI_SCK_PIN 14
#define MY_SOFT_SPI_MISO_PIN 16 #define MY_SOFT_SPI_MISO_PIN 16
#define MY_SOFT_SPI_MOSI_PIN 15 #define MY_SOFT_SPI_MOSI_PIN 15
#endif #endif
// When W5100 is connected we have to move CE/CSN pins for NRF radio // When W5100 is connected we have to move CE/CSN pins for NRF radio
#ifndef MY_RF24_CE_PIN #ifndef MY_RF24_CE_PIN
#define MY_RF24_CE_PIN 5 #define MY_RF24_CE_PIN 5
#endif #endif
#ifndef MY_RF24_CS_PIN #ifndef MY_RF24_CS_PIN
#define MY_RF24_CS_PIN 6 #define MY_RF24_CS_PIN 6
#endif #endif
@@ -106,28 +106,27 @@
#define MY_IP_GATEWAY_ADDRESS 192,168,178,1 #define MY_IP_GATEWAY_ADDRESS 192,168,178,1
#define MY_IP_SUBNET_ADDRESS 255,255,255,0 #define MY_IP_SUBNET_ADDRESS 255,255,255,0
// MQTT broker ip address or url. Define one or the other. // MQTT broker ip address or url. Define one or the other.
//#define MY_CONTROLLER_URL_ADDRESS "m20.cloudmqtt.com" //#define MY_CONTROLLER_URL_ADDRESS "m20.cloudmqtt.com"
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 #define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
// The MQTT broker port to to open // The MQTT broker port to to open
#define MY_PORT 1883 #define MY_PORT 1883
/* /*
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Enable inclusion mode // Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE //#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3 //#define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Flash leds on rx/tx/err
// Uncomment to override default HW configurations // Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin //#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin //#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
@@ -137,17 +136,14 @@
#include <Ethernet.h> #include <Ethernet.h>
#include <MySensors.h> #include <MySensors.h>
void setup() { void setup() {
} }
void presentation() { void presentation() {
// Present locally attached sensors here // Present locally attached sensors here
} }
void loop() { void loop() {
// Send locally attached sensors data here // Send locally attached sensors data here
} }
examples/SensebenderGatewaySerial/SensebenderGatewaySerial.ino
+24 -25
View File
@@ -19,33 +19,33 @@
******************************* *******************************
* *
* DESCRIPTION * DESCRIPTION
* The ArduinoGateway prints data received from sensors on the serial link. * The ArduinoGateway prints data received from sensors on the serial link.
* The gateway accepts input on seral which will be sent out on radio network. * The gateway accepts input on seral which will be sent out on radio network.
* *
* This GW code is designed for Sensebender GateWay / Arduino Zero * This GW code is designed for Sensebender GateWay / Arduino Zero
* *
* Wire connections (OPTIONAL): * Wire connections (OPTIONAL):
* - Inclusion button should be connected between digital pin 3 and GND * - Inclusion button should be connected between digital pin 3 and GND
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series * - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
* *
* LEDs (OPTIONAL): * LEDs (OPTIONAL):
* - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h * - To use the feature, uncomment any of the MY_DEFAULT_xx_LED_PINs
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
* - ERR (red) - fast blink on error during transmission error or recieve crc error * - ERR (red) - fast blink on error during transmission error or recieve crc error
* *
*/ */
#define SKETCH_VERSION "0.1" #define SKETCH_VERSION "0.1"
// Enable debug prints to serial monitor // Enable debug prints to serial monitor
#define MY_DEBUG #define MY_DEBUG
// Enable and select radio type attached // Enable and select radio type attached
#define MY_RADIO_NRF24 #define MY_RADIO_NRF24
//#define MY_RADIO_RFM69 //#define MY_RADIO_RFM69
// Set LOW transmit power level as default, if you have an amplified NRF-module and // Set LOW transmit power level as default, if you have an amplified NRF-module and
// power your radio separately with a good regulator you can turn up PA level. // power your radio separately with a good regulator you can turn up PA level.
#define MY_RF24_PA_LEVEL RF24_PA_HIGH #define MY_RF24_PA_LEVEL RF24_PA_HIGH
// Enable serial gateway // Enable serial gateway
@@ -56,14 +56,6 @@
#define MY_BAUD_RATE 38400 #define MY_BAUD_RATE 38400
#endif #endif
// Flash leds on rx/tx/err
#define MY_LEDS_BLINKING_FEATURE
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE
// Enable inclusion mode // Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway // Enable Inclusion mode button on gateway
@@ -73,10 +65,17 @@
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP //#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
// Set inclusion mode duration (in seconds) // Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60 #define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button // Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3 //#define MY_INCLUSION_MODE_BUTTON_PIN 3
// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300
// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE
// Flash leds on rx/tx/err
// Uncomment to override default HW configurations // Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin //#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
//#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin //#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin
@@ -93,16 +92,16 @@ Sd2Card card;
static uint8_t num_of_leds = 5; static uint8_t num_of_leds = 5;
static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE}; static uint8_t leds[] = {LED_BLUE, LED_RED, LED_GREEN, LED_YELLOW, LED_ORANGE};
void setup() { void setup() {
// Setup locally attached sensors // Setup locally attached sensors
} }
void presentation() { void presentation() {
// Present locally attached sensors // Present locally attached sensors
} }
void loop() { void loop() {
// Send locally attached sensor data here // Send locally attached sensor data here
} }
@@ -142,7 +141,7 @@ void preHwInit() {
digitalWrite(LED_YELLOW, HIGH); digitalWrite(LED_YELLOW, HIGH);
tests++; tests++;
} }
if (testEEProm()) { if (testEEProm()) {
digitalWrite(LED_ORANGE, HIGH); digitalWrite(LED_ORANGE, HIGH);
tests++; tests++;
@@ -155,7 +154,7 @@ void preHwInit() {
digitalWrite(leds[i], LOW); digitalWrite(leds[i], LOW);
} }
} }
} }
else { else {
while (1) { while (1) {
digitalWrite(LED_RED, HIGH); digitalWrite(LED_RED, HIGH);
@@ -164,7 +163,7 @@ void preHwInit() {
delay(200); delay(200);
} }
} }
} }
bool testSha204(){ bool testSha204(){
@@ -243,7 +242,7 @@ bool testEEProm() {
delay(500); delay(500);
eeprom_d2 = i2c_eeprom_read_byte(EEPROM_VERIFICATION_ADDRESS); eeprom_d2 = i2c_eeprom_read_byte(EEPROM_VERIFICATION_ADDRESS);
if (eeprom_d1 == eeprom_d2) { if (eeprom_d1 == eeprom_d2) {
SerialUSB.println("PASSED"); SerialUSB.println("PASSED");
i2c_eeprom_write_byte(EEPROM_VERIFICATION_ADDRESS, ~eeprom_d1); i2c_eeprom_write_byte(EEPROM_VERIFICATION_ADDRESS, ~eeprom_d1);
return true; return true;
} }
keywords.txt
+1 -2
View File
@@ -52,7 +52,6 @@ MY_PARENT_NODE_IS_STATIC LITERAL1
MY_OTA_FIRMWARE_FEATURE LITERAL1 MY_OTA_FIRMWARE_FEATURE LITERAL1
MY_OTA_FLASH_SS LITERAL1 MY_OTA_FLASH_SS LITERAL1
MY_OTA_FLASH_JDECID LITERAL1 MY_OTA_FLASH_JDECID LITERAL1
MY_LEDS_BLINKING_FEATURE LITERAL1
MY_WITH_LEDS_BLINKING_INVERSE LITERAL1 MY_WITH_LEDS_BLINKING_INVERSE LITERAL1
MY_DEFAULT_LED_BLINK_PERIOD LITERAL1 MY_DEFAULT_LED_BLINK_PERIOD LITERAL1
MY_WITH_LEDS_BLINKING_INVERSE LITERAL1 MY_WITH_LEDS_BLINKING_INVERSE LITERAL1
@@ -129,4 +128,4 @@ MY_NODE_UNLOCK_PIN LITERAL1
MY_NODE_LOCK_COUNTER_MAX LITERAL1 MY_NODE_LOCK_COUNTER_MAX LITERAL1
MY_SPIFLASH_SST25TYPE LITERAL1 MY_SPIFLASH_SST25TYPE LITERAL1
MY_CRITICAL_SECTION LITERAL1 MY_CRITICAL_SECTION LITERAL1
MY_RX_MESSAGE_BUFFER_SIZE LITERAL1 MY_RX_MESSAGE_BUFFER_SIZE LITERAL1