Move master branch from from mios git repo

2014-01-23 00:23:15 +01:00
commit 609d9e5be9
352 changed files with 53418 additions and 0 deletions
@@ -0,0 +1,109 @@
+# Name: Makefile
+
+# This is a prototype Makefile. Modify it according to your needs.
+# You should at least check the settings for
+# DEVICE ....... The AVR device you compile for
+# CLOCK ........ Target AVR clock rate in Hertz
+# OBJECTS ...... The object files created from your source files. This list is
+#                usually the same as the list of source files with suffix ".o".
+# PROGRAMMER ... Options to avrdude which define the hardware you use for
+#                uploading to the AVR and the interface where this hardware
+#                is connected.
+# FUSES ........ Parameters for avrdude to flash the fuses appropriately.
+
+DEVICE     = at90usb162
+CLOCK      = 16000000
+PROGRAMMER = -c stk500v2 -P avrdoper
+#OBJECTS    = $(TARGET).o
+FUSES      = -U hfuse:w:0xd9:m -U lfuse:w:0x24:m
+# ATMega8 fuse bits (fuse bits for other devices are different!):
+# Example for 8 MHz internal oscillator
+# Fuse high byte:
+# 0xd9 = 1 1 0 1   1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000)
+#        ^ ^ ^ ^   ^ ^ ^------ BOOTSZ0
+#        | | | |   | +-------- BOOTSZ1
+#        | | | |   +---------- EESAVE (set to 0 to preserve EEPROM over chip erase)
+#        | | | +-------------- CKOPT (clock option, depends on oscillator type)
+#        | | +---------------- SPIEN (if set to 1, serial programming is disabled)
+#        | +------------------ WDTON (if set to 0, watchdog is always on)
+#        +-------------------- RSTDISBL (if set to 0, RESET pin is disabled)
+# Fuse low byte:
+# 0x24 = 0 0 1 0   0 1 0 0
+#        ^ ^ \ /   \--+--/
+#        | |  |       +------- CKSEL 3..0 (8M internal RC)
+#        | |  +--------------- SUT 1..0 (slowly rising power)
+#        | +------------------ BODEN (if 0, brown-out detector is enabled)
+#        +-------------------- BODLEVEL (if 0: 4V, if 1: 2.7V)
+
+# Example for 12 MHz external crystal:
+# Fuse high byte:
+# 0xc9 = 1 1 0 0   1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000)
+#        ^ ^ ^ ^   ^ ^ ^------ BOOTSZ0
+#        | | | |   | +-------- BOOTSZ1
+#        | | | |   +---------- EESAVE (set to 0 to preserve EEPROM over chip erase)
+#        | | | +-------------- CKOPT (clock option, depends on oscillator type)
+#        | | +---------------- SPIEN (if set to 1, serial programming is disabled)
+#        | +------------------ WDTON (if set to 0, watchdog is always on)
+#        +-------------------- RSTDISBL (if set to 0, RESET pin is disabled)
+# Fuse low byte:
+# 0x9f = 1 0 0 1   1 1 1 1
+#        ^ ^ \ /   \--+--/
+#        | |  |       +------- CKSEL 3..0 (external >8M crystal)
+#        | |  +--------------- SUT 1..0 (crystal osc, BOD enabled)
+#        | +------------------ BODEN (if 0, brown-out detector is enabled)
+#        +-------------------- BODLEVEL (if 0: 4V, if 1: 2.7V)
+
+
+# Tune the lines below only if you know what you are doing:
+
+AVRDUDE = avrdude $(PROGRAMMER) -p $(DEVICE)
+COMPILE = avr-gcc $(CFLAGS) -Wall -std=gnu99 -funsigned-char -funsigned-bitfields -ffunction-sections -fpack-struct -fshort-enums -I. -Os -DF_CPU=$(CLOCK) -mmcu=$(DEVICE)
+
+# symbolic targets:
+all:	$(TARGET).hex
+
+.c.o:
+	$(COMPILE) -c $< -o $@
+
+.S.o:
+	$(COMPILE) -x assembler-with-cpp -c $< -o $@
+# "-x assembler-with-cpp" should not be necessary since this is the default
+# file type for the .S (with capital S) extension. However, upper case
+# characters are not always preserved on Windows. To ensure WinAVR
+# compatibility define the file type manually.
+
+.c.s:
+	$(COMPILE) -S $< -o $@
+
+flash:	all
+	$(AVRDUDE) -U flash:w:$(TARGET).hex:i
+
+fuse:
+	$(AVRDUDE) $(FUSES)
+
+# Xcode uses the Makefile targets "", "clean" and "install"
+install: flash fuse
+
+# if you use a bootloader, change the command below appropriately:
+load: all
+	bootloadHID $(TARGET).hex
+
+clean:
+	rm -f $(TARGET).hex $(TARGET).elf $(OBJECTS)
+
+# file targets:
+$(TARGET).elf: $(OBJECTS)
+	$(COMPILE) -o $(TARGET).elf $(OBJECTS)
+
+$(TARGET).hex: $(TARGET).elf
+	rm -f $(TARGET).hex
+	avr-objcopy -j .text -j .data -O ihex $(TARGET).elf $(TARGET).hex
+# If you have an EEPROM section, you must also create a hex file for the
+# EEPROM and add it to the "flash" target.
+
+# Targets for code debugging and analysis:
+disasm:	$(TARGET).elf
+	avr-objdump -d $(TARGET).elf
+
+cpp:
+	$(COMPILE) -E $(TARGET).c