Move master branch from from mios git repo

2014-01-23 00:23:15 +01:00
commit 609d9e5be9
352 changed files with 53418 additions and 0 deletions
@@ -0,0 +1,109 @@
+/*
+ * This sketch demonstrates how to use InterruptChain to receive and
+ * decode remote switches (old and new) and remote sensors.
+ *
+ * Basically, this sketch combines the features of the ShowReceivedCode
+ * and ShowReceivedCodeNewKaku examples of RemoteSwitch and the
+ * ThermoHygroReceiver of RemoteSensor all at the same time!
+ *
+ * After uploading, enable the serial monitor at 115200 baud.
+ * When you press buttons on a 433MHz remote control, as supported by 
+ * RemoteSwitch or NewRemoteSwitch, the code will be echoed.
+ * At the same time, if data of a remote thermo/hygro-sensor is
+ * received, as supported by RemoteSensor, it will be echoed as well.
+ *
+ * Setup:
+ * - connect a 433MHz receiver on digital pin 2.
+ */
+
+#include <RemoteReceiver.h>
+#include <NewRemoteReceiver.h>
+#include <SensorReceiver.h>
+#include <InterruptChain.h>
+
+void setup() {
+  Serial.begin(115200);
+
+  // Interrupt -1 to indicate you will call the interrupt handler with InterruptChain
+  RemoteReceiver::init(-1, 2, showOldCode);
+  
+  // Again, interrupt -1 to indicate you will call the interrupt handler with InterruptChain
+  NewRemoteReceiver::init(-1, 2, showNewCode);
+
+  // And once more, interrupt -1 to indicate you will call the interrupt handler with InterruptChain
+  SensorReceiver::init(-1, showTempHumi);
+
+  // On interrupt, call the interrupt handlers of remote and sensor receivers
+  InterruptChain::addInterruptCallback(0, RemoteReceiver::interruptHandler);
+  InterruptChain::addInterruptCallback(0, NewRemoteReceiver::interruptHandler);
+  InterruptChain::addInterruptCallback(0, SensorReceiver::interruptHandler);
+}
+
+void loop() {
+   // You can do other stuff here!
+}
+
+// shows the received code sent from an old-style remote switch
+void showOldCode(unsigned long receivedCode, unsigned int period) {
+  // Print the received code.
+  Serial.print("Code: ");
+  Serial.print(receivedCode);
+  Serial.print(", period: ");
+  Serial.print(period);
+  Serial.println("us.");
+}
+
+// Shows the received code sent from an new-style remote switch
+void showNewCode(NewRemoteCode receivedCode) {
+  // Print the received code.
+  Serial.print("Addr ");
+  Serial.print(receivedCode.address);
+  
+  if (receivedCode.groupBit) {
+    Serial.print(" group");
+  } else {
+    Serial.print(" unit ");
+    Serial.print(receivedCode.unit);
+  }
+  
+  switch (receivedCode.switchType) {
+    case NewRemoteCode::off:
+      Serial.print(" off");
+      break;
+    case NewRemoteCode::on:
+      Serial.print(" on");
+      break;
+    case NewRemoteCode::dim:
+      Serial.print(" dim level ");
+      Serial.print(receivedCode.dimLevel);
+      break;
+    case NewRemoteCode::on_with_dim:
+      Serial.print(" on with dim level ");
+      Serial.print(receivedCode.dimLevel);
+      break;
+  }
+  
+  Serial.print(", period: ");
+  Serial.print(receivedCode.period);
+  Serial.println("us.");
+}
+
+// Shows the received sensor data
+void showTempHumi(byte *data) {
+  // is data a ThermoHygro-device?
+  if ((data[3] & 0x1f) == 0x1e) {
+    // Yes!
+    byte channel, randomId;
+    int temp;
+    byte humidity;
+
+    // Decode the data
+    SensorReceiver::decodeThermoHygro(data, channel, randomId, temp, humidity);
+  
+    // Print temperature. Note: temp is 10x the actual temperature!
+    Serial.print("Temperature: ");
+    Serial.print(temp / 10); // units
+    Serial.print('.');
+    Serial.println(temp % 10); // decimal
+  }
+}