diff --git a/libraries/MySensors/MyConfig.h b/libraries/MySensors/MyConfig.h
index fd6358c..b259a1c 100644
--- a/libraries/MySensors/MyConfig.h
+++ b/libraries/MySensors/MyConfig.h
@@ -31,6 +31,7 @@
 #define RF24_CE_PIN		   9
 #define RF24_CS_PIN		   10
 #define RF24_PA_LEVEL 	   RF24_PA_MAX
+#define RF24_PA_LEVEL_GW   RF24_PA_LOW
 #define RF24_CHANNEL	   76             //RF channel for the sensor net, 0-127
 #define RF24_DATARATE 	   RF24_250KBPS   //RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
 #define RF24_BASE_RADIO_ID ((uint64_t)0xA8A8E1FC00LL) // This is also act as base value for sensor nodeId addresses. Change this (or channel) if you have more than one sensor network.
diff --git a/libraries/MySensors/examples/EthernetGateway/EthernetGateway.ino b/libraries/MySensors/examples/EthernetGateway/EthernetGateway.ino
index 26fe33f..def707b 100644
--- a/libraries/MySensors/examples/EthernetGateway/EthernetGateway.ino
+++ b/libraries/MySensors/examples/EthernetGateway/EthernetGateway.ino
@@ -43,6 +43,8 @@
 #include <DigitalIO.h>     // This include can be removed when using UIPEthernet module  
 #include <SPI.h>  
 
+#include <MySigningDriverNone.h>
+#include <MyRFDriverNRF24.h>
 #include <MyParserSerial.h>  
 #include <MySensor.h>  
 #include <stdarg.h>
@@ -69,8 +71,12 @@
 #define RADIO_TX_LED_PIN    9  // the PCB, on board LED
 
 
-MySensor gw;
-
+// NRFRF24L01 radio driver (set low transmit power by default) 
+MyRFDriverNRF24 radio(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);  
+// Message signing driver (none default)
+MySigningDriverNone signer;
+// Construct MySensors library
+MySensor gw(radio, signer);
 
 #define IP_PORT 5003        // The port you want to open 
 IPAddress myIp (192, 168, 178, 66);  // Configure your static ip-address here    COMPILE ERROR HERE? Use Arduino IDE 1.5.7 or later!
diff --git a/libraries/MySensors/examples/MQTTGateway/MQTTGateway.ino b/libraries/MySensors/examples/MQTTGateway/MQTTGateway.ino
index bea3ef4..706ca3c 100644
--- a/libraries/MySensors/examples/MQTTGateway/MQTTGateway.ino
+++ b/libraries/MySensors/examples/MQTTGateway/MQTTGateway.ino
@@ -56,6 +56,8 @@ http://forum.mysensors.org/topic/303/mqtt-broker-gateway
 
 */
 
+#include <MySigningDriverNone.h>
+#include <MyRFDriverNRF24.h>
 #include <SPI.h>
 #include <MySensor.h>
 #include <MsTimer2.h>
@@ -89,7 +91,13 @@ uint8_t TCP_MAC[] = { 0x02, 0xDE, 0xAD, 0x00, 0x00, 0x42 };	// Mac-address - You
 
 //////////////////////////////////////////////////////////////////
 
-MySensor gw;
+// NRFRF24L01 radio driver (set low transmit power by default) 
+MyRFDriverNRF24 radio(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);  
+// Message signing driver (none default)
+MySigningDriverNone signer;
+// Construct MySensors library
+MySensor gw(radio, signer);
+
 EthernetServer server = EthernetServer(TCP_PORT);
 MyMessage msg;
 char convBuf[MAX_PAYLOAD*2+1];
diff --git a/libraries/MySensors/examples/SerialGateway/SerialGateway.ino b/libraries/MySensors/examples/SerialGateway/SerialGateway.ino
index dddacdb..c178b19 100644
--- a/libraries/MySensors/examples/SerialGateway/SerialGateway.ino
+++ b/libraries/MySensors/examples/SerialGateway/SerialGateway.ino
@@ -23,6 +23,8 @@
 
 #define NO_PORTB_PINCHANGES  
 
+#include <MySigningDriverNone.h>
+#include <MyRFDriverNRF24.h>
 #include <SPI.h>  
 #include <MyParserSerial.h>  
 #include <MySensor.h>  
@@ -38,7 +40,12 @@
 #define RADIO_TX_LED_PIN    5  // the PCB, on board LED
 
 
-MySensor gw;
+// NRFRF24L01 radio driver (set low transmit power by default) 
+MyRFDriverNRF24 radio(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);  
+// Message signing driver (none default)
+MySigningDriverNone signer;
+// Construct MySensors library
+MySensor gw(radio, signer);
 
 char inputString[MAX_RECEIVE_LENGTH] = "";    // A string to hold incoming commands from serial/ethernet interface
 int inputPos = 0;