fixed crlf for project
This commit is contained in:
Henrik Ekblad
@@ -1,79 +1,79 @@
|
||||
#include <spi.h>
|
||||
#include <ds1305.h>
|
||||
|
||||
#define DS1305_PIN 4
|
||||
#define LED_PIN 3
|
||||
|
||||
// following two methods required by DS1305 library to select/deselect device
|
||||
void select_ds1305(void)
|
||||
{
|
||||
digitalWrite(DS1305_PIN, HIGH);
|
||||
}
|
||||
|
||||
void deselect_ds1305(void)
|
||||
{
|
||||
digitalWrite(DS1305_PIN, LOW);
|
||||
}
|
||||
|
||||
// flash led that's connected to pin 3
|
||||
void flash_led(void)
|
||||
{
|
||||
pinMode(LED_PIN, OUTPUT);
|
||||
for (int i=0; i<10; i++) {
|
||||
digitalWrite(LED_PIN, i%2==0);
|
||||
delay(50);
|
||||
}
|
||||
}
|
||||
|
||||
// called when pin INT0 goes from 1 to 0
|
||||
ISR(INT0_vect)
|
||||
{
|
||||
// get alarm value to clear alarm interrupt flag on DS1305
|
||||
DS1305_DATETIME alarm;
|
||||
get_alarm0(&alarm);
|
||||
flash_led();
|
||||
}
|
||||
|
||||
void setup()
|
||||
{
|
||||
// flash LED at start to indicate were about to start
|
||||
flash_led();
|
||||
flash_led();
|
||||
|
||||
// pin used to enable DS1305
|
||||
pinMode(DS1305_PIN, OUTPUT);
|
||||
|
||||
// Make sure ADC is unselected and setup spi
|
||||
deselect_ds1305();
|
||||
setup_spi(SPI_MODE_1, SPI_MSB, SPI_NO_INTERRUPT, SPI_MSTR_CLK16);
|
||||
set_control(0);
|
||||
|
||||
// set current date/time to Thursday 06/05/09 20:32:30
|
||||
DS1305_DATETIME current = {0x30, 0x32, 0x20, 0x05, 0x06, 0x05, 0x09};
|
||||
set_time(¤t);
|
||||
|
||||
// change the value of alarm to the required time/granularity:
|
||||
// raise alarm every day (at 20:32:00):
|
||||
// DS1305_DATETIME alarm = {0x00, 0x32, 0x20, 0x00 | DS1305_ALARM_SET};
|
||||
// raise alarm every minute (when seconds = 00):
|
||||
// DS1305_DATETIME alarm = {0x00, 0x32 | DS1305_ALARM_SET,
|
||||
// 0x20 | DS1305_ALARM_SET, 0x05 | DS1305_ALARM_SET};
|
||||
// raise alarm every second:
|
||||
DS1305_DATETIME alarm = {0x55 | DS1305_ALARM_SET, 0x32 | DS1305_ALARM_SET,
|
||||
0x20 | DS1305_ALARM_SET, 0x05 | DS1305_ALARM_SET};
|
||||
set_alarm0(&alarm);
|
||||
// turn on timer and make alarm0 lower INT0 pin when alarm is triggered
|
||||
set_control(DS1305_EOSC | DS1305_INTCN | DS1305_AIE0);
|
||||
|
||||
// raise interrupt when INT0 pin falls (pin PD0 at AT90usbXXX, pin PD2 on ATmegaXXX (arduino pin 2))
|
||||
// the code in ISR(INT0_vect) above will be called
|
||||
EICRA = (1<<ISC01) | (0<<ISC00);
|
||||
// enable interrupts
|
||||
EIMSK = (1<<INT0);
|
||||
sei();
|
||||
}
|
||||
|
||||
void loop()
|
||||
{
|
||||
// do nothing - all action happens in interrupt
|
||||
}
|
||||
#include <spi.h>
|
||||
#include <ds1305.h>
|
||||
|
||||
#define DS1305_PIN 4
|
||||
#define LED_PIN 3
|
||||
|
||||
// following two methods required by DS1305 library to select/deselect device
|
||||
void select_ds1305(void)
|
||||
{
|
||||
digitalWrite(DS1305_PIN, HIGH);
|
||||
}
|
||||
|
||||
void deselect_ds1305(void)
|
||||
{
|
||||
digitalWrite(DS1305_PIN, LOW);
|
||||
}
|
||||
|
||||
// flash led that's connected to pin 3
|
||||
void flash_led(void)
|
||||
{
|
||||
pinMode(LED_PIN, OUTPUT);
|
||||
for (int i=0; i<10; i++) {
|
||||
digitalWrite(LED_PIN, i%2==0);
|
||||
delay(50);
|
||||
}
|
||||
}
|
||||
|
||||
// called when pin INT0 goes from 1 to 0
|
||||
ISR(INT0_vect)
|
||||
{
|
||||
// get alarm value to clear alarm interrupt flag on DS1305
|
||||
DS1305_DATETIME alarm;
|
||||
get_alarm0(&alarm);
|
||||
flash_led();
|
||||
}
|
||||
|
||||
void setup()
|
||||
{
|
||||
// flash LED at start to indicate were about to start
|
||||
flash_led();
|
||||
flash_led();
|
||||
|
||||
// pin used to enable DS1305
|
||||
pinMode(DS1305_PIN, OUTPUT);
|
||||
|
||||
// Make sure ADC is unselected and setup spi
|
||||
deselect_ds1305();
|
||||
setup_spi(SPI_MODE_1, SPI_MSB, SPI_NO_INTERRUPT, SPI_MSTR_CLK16);
|
||||
set_control(0);
|
||||
|
||||
// set current date/time to Thursday 06/05/09 20:32:30
|
||||
DS1305_DATETIME current = {0x30, 0x32, 0x20, 0x05, 0x06, 0x05, 0x09};
|
||||
set_time(¤t);
|
||||
|
||||
// change the value of alarm to the required time/granularity:
|
||||
// raise alarm every day (at 20:32:00):
|
||||
// DS1305_DATETIME alarm = {0x00, 0x32, 0x20, 0x00 | DS1305_ALARM_SET};
|
||||
// raise alarm every minute (when seconds = 00):
|
||||
// DS1305_DATETIME alarm = {0x00, 0x32 | DS1305_ALARM_SET,
|
||||
// 0x20 | DS1305_ALARM_SET, 0x05 | DS1305_ALARM_SET};
|
||||
// raise alarm every second:
|
||||
DS1305_DATETIME alarm = {0x55 | DS1305_ALARM_SET, 0x32 | DS1305_ALARM_SET,
|
||||
0x20 | DS1305_ALARM_SET, 0x05 | DS1305_ALARM_SET};
|
||||
set_alarm0(&alarm);
|
||||
// turn on timer and make alarm0 lower INT0 pin when alarm is triggered
|
||||
set_control(DS1305_EOSC | DS1305_INTCN | DS1305_AIE0);
|
||||
|
||||
// raise interrupt when INT0 pin falls (pin PD0 at AT90usbXXX, pin PD2 on ATmegaXXX (arduino pin 2))
|
||||
// the code in ISR(INT0_vect) above will be called
|
||||
EICRA = (1<<ISC01) | (0<<ISC00);
|
||||
// enable interrupts
|
||||
EIMSK = (1<<INT0);
|
||||
sei();
|
||||
}
|
||||
|
||||
void loop()
|
||||
{
|
||||
// do nothing - all action happens in interrupt
|
||||
}
|
||||
|
||||
+111
-111
@@ -1,111 +1,111 @@
|
||||
This directory contains a simple AVR spi helper library that should
|
||||
run on most AVR microcontrollers which support SPI.
|
||||
|
||||
The code is further described at:
|
||||
http://www.rocketnumbernine.com/2009/04/26/using-spi-on-an-avr-1/ (basics & ADC)
|
||||
http://www.rocketnumbernine.com/2009/05/12/using-spi-on-an-avr-2/ (RTC)
|
||||
|
||||
Any comments/questions to <andrew@rocketnumbernine.com>
|
||||
|
||||
Make sure viewing this text in a fixed width font for the tables and diagrams
|
||||
|
||||
|
||||
----------------------------------
|
||||
Arduino
|
||||
----------------------------------
|
||||
The Arduino Directory contains all code required to run on the Arduino.
|
||||
Simply copy the Arduino/SPI and Arduino/DS1305 directories to the
|
||||
"hardware/libraries" directory of your Arduino IDE installation and
|
||||
restart the Arduino IDE. Once restarted there should be
|
||||
"Sketch->Import Library->SPI" and "Sketch->Import Library->DS1305" menu
|
||||
entries which can be used to include the spi header files into your project.
|
||||
"File->Sketchbook->Examples->Library SPI" contains 3 example projects
|
||||
|
||||
|
||||
----------------------------------
|
||||
AVR GCC
|
||||
----------------------------------
|
||||
To use, just copy spi.h and spi.c (and ds1305.c and ds1305.h if using
|
||||
the DS1305 Real Time Clock chip) to your own project and compile.
|
||||
|
||||
Makefile.mf - 'standard' generated make file from AVR GCC
|
||||
Makefile - Makefile "make examples" will make example programs below:
|
||||
|
||||
spi-test-adc.c MC3201 Analogue to Digital convertor example
|
||||
spi-test-rtc.c DS1305 - Real-Time-Clock/Alarm example
|
||||
spi-test-masterslave.c Master/Slave communication example
|
||||
|
||||
|
||||
----------------------------------
|
||||
PINS
|
||||
----------------------------------
|
||||
Following are the AVR pins used in the circuits below
|
||||
|
||||
ATmegaXXX Arduino AT90usbXXX
|
||||
MISO PB4 12 PB3
|
||||
MOSI PB3 11 PB2
|
||||
SCK PB5 13 PB1
|
||||
SS PB2 10 PB0
|
||||
|
||||
INT0 PD2 2 PD0
|
||||
|
||||
|
||||
----------------------------------
|
||||
MC3201 12-bit ADC Circuit
|
||||
----------------------------------
|
||||
See http://ww1.microchip.com/downloads/en/DeviceDoc/21290D.pdf for full details.
|
||||
|
||||
+-----------------+
|
||||
| MC3201 |
|
||||
+5V [| Vref Vdd |] +5V
|
||||
| |
|
||||
Analogue In [| IN+ CLK |] AVR SCK
|
||||
| |
|
||||
Ground [| IN- Dout |] AVR MOSI
|
||||
| |
|
||||
Ground [| Vss ^CS |] AVR CE
|
||||
+-----------------+
|
||||
|
||||
|
||||
For testing purposes "Analogue In" can be connected to the middle wire
|
||||
of a potentiometer with one outer wire being connected to +5 and the
|
||||
other to Ground. A 1uF Capacitor should be placed between the analogue
|
||||
input and ground, and +5V and ground as close to the chip as possible,
|
||||
but in a pinch the circuit will likely work without.
|
||||
|
||||
|
||||
MOSI/SLCK/CE to the relevant pin on the AVR (MISO is not used) - see above.
|
||||
|
||||
----------------------------------
|
||||
DS1305 Real Time Clock Circuit
|
||||
----------------------------------
|
||||
See http://datasheets.maxim-ic.com/en/ds/DS1305.pdf for full details.
|
||||
|
||||
Without a battery the following connections can be used:
|
||||
|
||||
+-----------------+
|
||||
| DS1305 |
|
||||
Ground [| Vcc2 Vcc1 |] +5V
|
||||
| |
|
||||
Ground [| Vbat ^PF |] Not Connected
|
||||
| |
|
||||
Crystal [| X1 Vccif |] +5V
|
||||
| |
|
||||
Crystal [| X2 SDO |] AVR MISO
|
||||
| |
|
||||
Not Connected [| N.C. SDI |] AVR MOSI
|
||||
| |
|
||||
AVR INT0 [| INT0 SLCK |] AVR SLCK
|
||||
| |
|
||||
Not Connected [| INT1 CE |] AVR CE
|
||||
| |
|
||||
Ground [| GND SERMODE |] +5V
|
||||
+-----------------+
|
||||
|
||||
|
||||
MISO/MOSI/SLCK/CE/INT0 to the relevant pin on the AVR - see above.
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
This directory contains a simple AVR spi helper library that should
|
||||
run on most AVR microcontrollers which support SPI.
|
||||
|
||||
The code is further described at:
|
||||
http://www.rocketnumbernine.com/2009/04/26/using-spi-on-an-avr-1/ (basics & ADC)
|
||||
http://www.rocketnumbernine.com/2009/05/12/using-spi-on-an-avr-2/ (RTC)
|
||||
|
||||
Any comments/questions to <andrew@rocketnumbernine.com>
|
||||
|
||||
Make sure viewing this text in a fixed width font for the tables and diagrams
|
||||
|
||||
|
||||
----------------------------------
|
||||
Arduino
|
||||
----------------------------------
|
||||
The Arduino Directory contains all code required to run on the Arduino.
|
||||
Simply copy the Arduino/SPI and Arduino/DS1305 directories to the
|
||||
"hardware/libraries" directory of your Arduino IDE installation and
|
||||
restart the Arduino IDE. Once restarted there should be
|
||||
"Sketch->Import Library->SPI" and "Sketch->Import Library->DS1305" menu
|
||||
entries which can be used to include the spi header files into your project.
|
||||
"File->Sketchbook->Examples->Library SPI" contains 3 example projects
|
||||
|
||||
|
||||
----------------------------------
|
||||
AVR GCC
|
||||
----------------------------------
|
||||
To use, just copy spi.h and spi.c (and ds1305.c and ds1305.h if using
|
||||
the DS1305 Real Time Clock chip) to your own project and compile.
|
||||
|
||||
Makefile.mf - 'standard' generated make file from AVR GCC
|
||||
Makefile - Makefile "make examples" will make example programs below:
|
||||
|
||||
spi-test-adc.c MC3201 Analogue to Digital convertor example
|
||||
spi-test-rtc.c DS1305 - Real-Time-Clock/Alarm example
|
||||
spi-test-masterslave.c Master/Slave communication example
|
||||
|
||||
|
||||
----------------------------------
|
||||
PINS
|
||||
----------------------------------
|
||||
Following are the AVR pins used in the circuits below
|
||||
|
||||
ATmegaXXX Arduino AT90usbXXX
|
||||
MISO PB4 12 PB3
|
||||
MOSI PB3 11 PB2
|
||||
SCK PB5 13 PB1
|
||||
SS PB2 10 PB0
|
||||
|
||||
INT0 PD2 2 PD0
|
||||
|
||||
|
||||
----------------------------------
|
||||
MC3201 12-bit ADC Circuit
|
||||
----------------------------------
|
||||
See http://ww1.microchip.com/downloads/en/DeviceDoc/21290D.pdf for full details.
|
||||
|
||||
+-----------------+
|
||||
| MC3201 |
|
||||
+5V [| Vref Vdd |] +5V
|
||||
| |
|
||||
Analogue In [| IN+ CLK |] AVR SCK
|
||||
| |
|
||||
Ground [| IN- Dout |] AVR MOSI
|
||||
| |
|
||||
Ground [| Vss ^CS |] AVR CE
|
||||
+-----------------+
|
||||
|
||||
|
||||
For testing purposes "Analogue In" can be connected to the middle wire
|
||||
of a potentiometer with one outer wire being connected to +5 and the
|
||||
other to Ground. A 1uF Capacitor should be placed between the analogue
|
||||
input and ground, and +5V and ground as close to the chip as possible,
|
||||
but in a pinch the circuit will likely work without.
|
||||
|
||||
|
||||
MOSI/SLCK/CE to the relevant pin on the AVR (MISO is not used) - see above.
|
||||
|
||||
----------------------------------
|
||||
DS1305 Real Time Clock Circuit
|
||||
----------------------------------
|
||||
See http://datasheets.maxim-ic.com/en/ds/DS1305.pdf for full details.
|
||||
|
||||
Without a battery the following connections can be used:
|
||||
|
||||
+-----------------+
|
||||
| DS1305 |
|
||||
Ground [| Vcc2 Vcc1 |] +5V
|
||||
| |
|
||||
Ground [| Vbat ^PF |] Not Connected
|
||||
| |
|
||||
Crystal [| X1 Vccif |] +5V
|
||||
| |
|
||||
Crystal [| X2 SDO |] AVR MISO
|
||||
| |
|
||||
Not Connected [| N.C. SDI |] AVR MOSI
|
||||
| |
|
||||
AVR INT0 [| INT0 SLCK |] AVR SLCK
|
||||
| |
|
||||
Not Connected [| INT1 CE |] AVR CE
|
||||
| |
|
||||
Ground [| GND SERMODE |] +5V
|
||||
+-----------------+
|
||||
|
||||
|
||||
MISO/MOSI/SLCK/CE/INT0 to the relevant pin on the AVR - see above.
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
Reference in New Issue
Block a user