ESPGateway work ongoing

libraries/MySensors/MyConfig.h

@@ -133,15 +133,27 @@
 #endif
 // The RX LED default pin
 #ifndef MY_DEFAULT_RX_LED_PIN
-#define MY_DEFAULT_RX_LED_PIN 6
+	#if defined(ARDUINO_ARCH_ESP8266)
+		#define MY_DEFAULT_RX_LED_PIN 8
+	#else
+		#define MY_DEFAULT_RX_LED_PIN 6
+	#endif
 #endif
 // The TX LED default pin
 #ifndef MY_DEFAULT_TX_LED_PIN
-#define MY_DEFAULT_TX_LED_PIN 5
+	#if defined(ARDUINO_ARCH_ESP8266)
+		#define MY_DEFAULT_TX_LED_PIN 9
+	#else
+		#define MY_DEFAULT_TX_LED_PIN 5
+	#endif
 #endif
 // The Error LED default pin
 #ifndef MY_DEFAULT_ERR_LED_PIN
-#define MY_DEFAULT_ERR_LED_PIN 4
+	#if defined(ARDUINO_ARCH_ESP8266)
+		#define MY_DEFAULT_ERR_LED_PIN 7
+	#else
+		#define MY_DEFAULT_ERR_LED_PIN 4
+	#endif
 #endif
 
 /**********************************************
@@ -160,7 +172,11 @@
 
 // The default input pin used for the inclusion mode button
 #ifndef MY_INCLUSION_MODE_BUTTON_PIN
-#define MY_INCLUSION_MODE_BUTTON_PIN 3
+	#if defined(ARDUINO_ARCH_ESP8266)
+		#define MY_INCLUSION_MODE_BUTTON_PIN 5
+	#else
+		#define MY_INCLUSION_MODE_BUTTON_PIN 3
+	#endif
 #endif
 // Number of seconds (default one minute) inclusion mode should be enabled
 #ifndef MY_INCLUSION_MODE_DURATION
@@ -220,17 +236,26 @@
 // Enables RF24 encryption (all nodes and gateway must have this enabled)
 //#define MY_RF24_ENABLE_ENCRYPTION
 
-// Default encrytion key. Override in sketch if needed.
+// Default encryption key. Override in sketch if needed.
 #ifndef MY_RF24_ENCRYPTKEY
 #define MY_RF24_ENCRYPTKEY 0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,0x10,0x11,0x12,0x13,0x14,0x15,0x16
 #endif
 
 // Default pin settings. Override in sketch if needed.
 #ifndef MY_RF24_CE_PIN
-#define MY_RF24_CE_PIN 9
+	#if defined(ARDUINO_ARCH_ESP8266)
+		#define MY_RF24_CE_PIN 4
+	#else
+		#define MY_RF24_CE_PIN 9
+	#endif
 #endif
+
 #ifndef MY_RF24_CS_PIN
-#define MY_RF24_CS_PIN 10
+	#if defined(ARDUINO_ARCH_ESP8266)
+		#define MY_RF24_CS_PIN 15
+	#else
+		#define MY_RF24_CS_PIN 10
+	#endif
 #endif
 
 #ifndef MY_RF24_PA_LEVEL

libraries/MySensors/MySensor.h

@@ -44,10 +44,11 @@
 
 // HARDWARE
 #if defined(ARDUINO_ARCH_ESP8266)
+	// Remove PSTR macros from debug prints
 	#undef PSTR
 	#define PSTR(x) (x)
-	#include "drivers/ESP8266/EEPROM/EEPROM.cpp"
+	/*#include "drivers/ESP8266/EEPROM/EEPROM.cpp"
-	#include "drivers/ESP8266/SPI/SPI.cpp"
+	#include "drivers/ESP8266/SPI/SPI.cpp"*/
 	#include "core/MyHwESP8266.cpp"
 	// For ESP8266, we always enable gateway feature
 	#define MY_GATEWAY_ESP8266
@@ -230,33 +231,21 @@
 #include "core/MySensorCore.cpp"
 
 extern void setup();
-//extern void loop();
-
 // Optional sketch functions called by MySensors library
 void receive(const MyMessage &message)  __attribute__((weak));
 void receiveTime(unsigned long)  __attribute__((weak));
 void presentation()  __attribute__((weak));
 extern "C" void setup()  __attribute__((weak));
 extern "C" void loop()  __attribute__((weak));
-
+extern "C" void loop2()  __attribute__((weak));
 
 #include <Arduino.h>
-// Initialize library and handle sketch functions like we want to
-int main(void) {
-	init();  // Init Arduino
-	#if defined(USBCON)
-		USBDevice.attach();
-	#endif
-	_begin(); // Startup MySensors library
-	if (setup) setup(); // Call sketch setup
 
-	for(;;) {
+#if defined(MY_GATEWAY_ESP8266)
-		_process();  // Process incoming data
+	#include "core/MyMainESP8266.cpp"
-		if (loop) loop(); // Call sketch loop
+#else
-		#if !defined(ARDUINO_ARCH_ESP8266)
+	#include "core/MyMainDefault.cpp"
-		if (serialEventRun) serialEventRun();
+#endif
-		#endif
+
-	}
+
-	return 0;
-}
 #endif

libraries/MySensors/core/MyGatewayTransportEthernet.cpp

@@ -86,6 +86,7 @@ bool gatewayTransportInit() {
 		{
 			delay(500);
 			Serial.print(".");
+			hwWatchdogReset();
 		}
 		Serial.println(PSTR("Connected to AP!"));
 		Serial.print(PSTR("IP: "));
@@ -168,17 +169,47 @@ bool gatewayTransportAvailable()
 			return protocolParse(_ethernetMsg, inputString[0]);
 		}
 	#else
-		// Loop over clients connect and read available data
+		// Go over list of clients and stop any that are no longer connected.
+		// If the server has a new client connection it will be assigned to a free slot.
+		bool allSlotsOccupied = true;
+		for (uint8_t i = 0; i < ARRAY_SIZE(clients); i++) {
+			if (!clients[i].connected()) {
+				if (clientsConnected[i]) {
+					Serial.print("Client ");
+					Serial.print(i);
+					Serial.println(" disconnected");
+					clients[i].stop();
+				}
+				//check if there are any new clients
+				if (_ethernetServer.hasClient()) {
+					clients[i] = _ethernetServer.available();
+					inputString[i].idx = 0;
+					Serial.print("Client ");
+					Serial.print(i);
+					Serial.println(" connected");
+					gatewayTransportSend(buildGw(_msg, I_GATEWAY_READY).set("Gateway startup complete."));
+				}
+			}
+			bool connected = clients[i].connected();
+			clientsConnected[i] = connected;
+			allSlotsOccupied &= connected;
+		}
+		if (allSlotsOccupied && _ethernetServer.hasClient()) {
+			//no free/disconnected spot so reject
+			Serial.println("No free slot available");
+			EthernetClient c = _ethernetServer.available();
+			c.stop();
+		}
+			// Loop over clients connect and read available data
 		for (uint8_t i = 0; i < ARRAY_SIZE(clients); i++) {
 			while (clients[i].connected() && clients[i].available()) {
 				char inChar = clients[i].read();
+				Serial.print(inChar);
 				if (inputString[i].idx < MY_GATEWAY_MAX_RECEIVE_LENGTH - 1) {
 					// if newline then command is complete
 					if (inChar == '\n') {
 						// a command was issued by the client
 						// we will now try to send it to the actuator
-						inputString[i].string[inputString[i].idx] = 0;
-
 						// echo the string to the serial port
 						Serial.print(PSTR("Client "));
 						Serial.print(i);
@@ -188,7 +219,11 @@ bool gatewayTransportAvailable()
 						// clear the string:
 						inputString[i].idx = 0;
 
-						return protocolParse(_ethernetMsg, inputString[i].string);
+						bool ret = protocolParse(_ethernetMsg, inputString[i].string);
+						inputString[i].string[inputString[i].idx] = 0;
+						if (ret)
+							return ret;
+
 					} else {
 						// add it to the inputString:
 						inputString[i].string[inputString[i].idx++] = inChar;

libraries/MySensors/core/MySensorCore.cpp

@@ -64,6 +64,7 @@ void _begin() {
 	    hwInit();
     #endif
 
+	debug(PSTR("Starting...\n"));
 	#if defined(MY_RADIO_FEATURE)
 		_failedTransmissions = 0;
 
@@ -74,7 +75,6 @@ void _begin() {
 		}
 	#endif
 
-
 	#if defined(MY_GATEWAY_FEATURE)
 		#if defined(MY_INCLUSION_BUTTON_FEATURE)
 	    	inclusionInit();
@@ -147,7 +147,8 @@ void _begin() {
 	#if defined(MY_RADIO_FEATURE)
 		transportPresentNode();
 	#endif
-
+	if (presentation)
+		presentation();
 	debug(PSTR("%s started, id=%d, parent=%d, distance=%d\n"), MY_NODE_TYPE, _nc.nodeId, _nc.parentNodeId, _nc.distance);
 }
 
@@ -232,7 +233,11 @@ void _processInternalMessages() {
 		hwWriteConfig(EEPROM_CONTROLLER_CONFIG_ADDRESS, isMetric);
 	} else if (type == I_PRESENTATION) {
 		// Re-send node presentation to controller
-		transportPresentNode();
+		#if defined(MY_RADIO_FEATURE)
+			transportPresentNode();
+		#endif
+		if (presentation)
+			presentation();
 	} else if (type == I_HEARTBEAT) {
 		if (!mGetAck(_msg)) {
 			// Send heartbeat ack message back to sender (with the same payload)

libraries/MySensors/core/MyTransport.cpp

@@ -540,8 +540,6 @@ void transportPresentNode() {
 			#endif
 		}
 	#endif
-	if (presentation)
-		presentation();
 }
 
 void transportFindParentNode() {

libraries/MySensors/core/MyTransportNRF24.cpp

@@ -44,11 +44,16 @@ uint8_t _paLevel;
 
 bool transportInit() {
 	// Start up the radio library
+	Serial.println("Radio1");
 	_rf24.begin();
+	Serial.println("Radio2");
 
 	if (!_rf24.isPVariant()) {
+		Serial.println("Radio3");
+
 		return false;
 	}
+	Serial.println("Radio4");
 	_rf24.setAutoAck(1);
 	_rf24.setAutoAck(BROADCAST_PIPE,false); // Turn off auto ack for broadcast
 	_rf24.enableAckPayload();
@@ -58,9 +63,11 @@ bool transportInit() {
 	_rf24.setRetries(5,15);
 	_rf24.setCRCLength(RF24_CRC_16);
 	_rf24.enableDynamicPayloads();
+	Serial.println("Radio5");
 
 	// All nodes listen to broadcast pipe (for FIND_PARENT_RESPONSE messages)
 	_rf24.openReadingPipe(BROADCAST_PIPE, TO_ADDR(BROADCAST_ADDRESS));
+	Serial.println("Radio6");
 
 
 	#if defined(MY_RF24_ENABLE_ENCRYPTION)

libraries/MySensors/examples/Esp8266Gateway/Esp8266Gateway.ino

@@ -65,11 +65,16 @@
  * Make sure to fill in your ssid and WiFi password below for ssid & pass.
  */
 
+#include <EEPROM.h>
+#include <SPI.h>
 #include <ESP8266WiFi.h>
 
 // Enable debug prints to serial monitor
 #define MY_DEBUG 
 
+// Use a bit lower baudrate here than default
+#define MY_BAUD_RATE 9600
+
 // Enable and select radio type (if attached)
 #define MY_RADIO_NRF24
 //#define MY_RADIO_RFM69
@@ -80,6 +85,8 @@
 #define MY_ESP8266_SSID "MySSID"
 #define MY_ESP8266_PASSWORD "MyVerySecretPassword"
 
+
+
 // Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
 // #define MY_IP_ADDRESS 192,168,178,66   
 // If using static ip you need to define Gateway and Subnet address as well
@@ -90,11 +97,12 @@
 #define MY_PORT 5003      
 
 // How many clients should be able to connect to this gateway (default 1)
-#define MY_GATEWAY_MAX_CLIENTS 5
+#define MY_GATEWAY_MAX_CLIENTS 2
 
 // Controller ip address (enables client mode). Undefine this to act as sever.
-//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
+
- 
+// #define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254   
+ /*
 // Flash leds on rx/tx/err
 #define MY_LEDS_BLINKING_FEATURE
 // Set blinking period
@@ -112,12 +120,11 @@
 #define MY_DEFAULT_ERR_LED_PIN 16  // Error led pin
 #define MY_DEFAULT_RX_LED_PIN  16  // Receive led pin
 #define MY_DEFAULT_TX_LED_PIN  16  // the PCB, on board LED
-
+*/
 
 #include <MySensor.h>
 
 void setup() { 
-  
 }
 
 void presentation() {
@@ -126,7 +133,8 @@ void presentation() {
 
 
 void loop() {
-
+  wait(500);
+  Serial.println("Hello");
 }