diff --git a/libraries/MySensors/examples/GatewayESP8266OTA/GatewayESP8266OTA.ino b/libraries/MySensors/examples/GatewayESP8266OTA/GatewayESP8266OTA.ino new file mode 100644 index 0000000..bb19188 --- /dev/null +++ b/libraries/MySensors/examples/GatewayESP8266OTA/GatewayESP8266OTA.ino @@ -0,0 +1,175 @@ +/** + * The MySensors Arduino library handles the wireless radio link and protocol + * between your home built sensors/actuators and HA controller of choice. + * The sensors forms a self healing radio network with optional repeaters. Each + * repeater and gateway builds a routing tables in EEPROM which keeps track of the + * network topology allowing messages to be routed to nodes. + * + * Created by Henrik Ekblad + * Copyright (C) 2013-2015 Sensnology AB + * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors + * + * Documentation: http://www.mysensors.org + * Support Forum: http://forum.mysensors.org + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + ******************************* + * + * REVISION HISTORY + * Version 1.0 - Henrik EKblad + * Contribution by tekka, + * Contribution by a-lurker and Anticimex, + * Contribution by Norbert Truchsess + * Contribution by Ivo Pullens (ESP8266 support) + * + * DESCRIPTION + * The EthernetGateway sends data received from sensors to the WiFi link. + * The gateway also accepts input on ethernet interface, which is then sent out to the radio network. + * + * VERA CONFIGURATION: + * Enter "ip-number:port" in the ip-field of the Arduino GW device. This will temporarily override any serial configuration for the Vera plugin. + * E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003 + * + * LED purposes: + * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h + * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved + * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly + * - ERR (red) - fast blink on error during transmission error or recieve crc error + * + * See http://www.mysensors.org/build/esp8266_gateway for wiring instructions. + * nRF24L01+ ESP8266 + * VCC VCC + * CE GPIO4 + * CSN/CS GPIO15 + * SCK GPIO14 + * MISO GPIO12 + * MOSI GPIO13 + * GND GND + * + * Not all ESP8266 modules have all pins available on their external interface. + * This code has been tested on an ESP-12 module. + * The ESP8266 requires a certain pin configuration to download code, and another one to run code: + * - Connect REST (reset) via 10K pullup resistor to VCC, and via switch to GND ('reset switch') + * - Connect GPIO15 via 10K pulldown resistor to GND + * - Connect CH_PD via 10K resistor to VCC + * - Connect GPIO2 via 10K resistor to VCC + * - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch') + * + * Inclusion mode button: + * - Connect GPIO5 via switch to GND ('inclusion switch') + * + * Hardware SHA204 signing is currently not supported! + * + * Make sure to fill in your ssid and WiFi password below for ssid & pass. + */ + +#include +#include +#include + +// Enable debug prints to serial monitor +#define MY_DEBUG + +// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h +#define MY_BAUD_RATE 9600 + +// Enables and select radio type (if attached) +#define MY_RADIO_NRF24 +//#define MY_RADIO_RFM69 + +#define MY_GATEWAY_ESP8266 + +#define MY_ESP8266_SSID "MySSID" +#define MY_ESP8266_PASSWORD "MyVerySecretPassword" + +// Enable UDP communication +//#define MY_USE_UDP + +// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP) +//#define MY_IP_ADDRESS 192,168,178,87 + +// If using static ip you need to define Gateway and Subnet address as well +#define MY_IP_GATEWAY_ADDRESS 192,168,178,1 +#define MY_IP_SUBNET_ADDRESS 255,255,255,0 + +// The port to keep open on node server mode +#define MY_PORT 5003 + +// How many clients should be able to connect to this gateway (default 1) +#define MY_GATEWAY_MAX_CLIENTS 2 + +// Controller ip address. Enables client mode (default is "server" mode). +// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere. +//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68 + +// Enable inclusion mode +#define MY_INCLUSION_MODE_FEATURE + +// Enable Inclusion mode button on gateway +// #define MY_INCLUSION_BUTTON_FEATURE +// Set inclusion mode duration (in seconds) +#define MY_INCLUSION_MODE_DURATION 60 +// Digital pin used for inclusion mode button +#define MY_INCLUSION_MODE_BUTTON_PIN 3 + + +// Flash leds on rx/tx/err +// #define MY_LEDS_BLINKING_FEATURE +// Set blinking period +// #define MY_DEFAULT_LED_BLINK_PERIOD 300 + +// Led pins used if blinking feature is enabled above +#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin +#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin +#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED + +#if defined(MY_USE_UDP) + #include +#else + #include +#endif + +#include + +void setup() { + + ArduinoOTA.onStart([]() { + Serial.println("ArduinoOTA start"); + }); + ArduinoOTA.onEnd([]() { + Serial.println("\nArduinoOTA end"); + }); + ArduinoOTA.onProgress([](unsigned int progress, unsigned int total) { + Serial.printf("OTA Progress: %u%%\r", (progress / (total / 100))); + }); + ArduinoOTA.onError([](ota_error_t error) { + Serial.printf("Error[%u]: ", error); + if (error == OTA_AUTH_ERROR) Serial.println("Auth Failed"); + else if (error == OTA_BEGIN_ERROR) Serial.println("Begin Failed"); + else if (error == OTA_CONNECT_ERROR) Serial.println("Connect Failed"); + else if (error == OTA_RECEIVE_ERROR) Serial.println("Receive Failed"); + else if (error == OTA_END_ERROR) Serial.println("End Failed"); + }); + ArduinoOTA.begin(); + Serial.println("Ready"); + Serial.print("IP address: "); + Serial.println(WiFi.localIP()); + +} + +void presentation() { + // Present locally attached sensors here +} + + +void loop() { + // Send locally attech sensors data here + ArduinoOTA.handle(); +} + + + +