MySmartHome/MySensors
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Fix: txStandBy hang. Updated Transfer example

Browse Source 
- txStandBy was hanging if the last of the data timed out. Now clears
the MAX_RT flag if timed out
- Finished updating example file Transfer.ino for demonstrating
half-rate transfers using the FIFO buffers
This commit is contained in:
TMRh20
2014-03-22 01:52:22 -06:00
parent 4d8da2f01d
commit f3b3fb1f44
3 changed files with 73 additions and 78 deletions
Download Patch File Download Diff File Expand all files Collapse all files
examples/Transfer/Transfer.ino
+46 -67
View File
@@ -19,105 +19,92 @@ TMRh20 2014
#include "RF24.h"
#include "printf.h"
// Hardware configuration
// Set up nRF24L01 radio on SPI bus plus pins 9 & 10
/************* USER Configuration *****************************/
// Hardware configuration
RF24 radio(48,49); // Set up nRF24L01 radio on SPI bus plus pins 9 & 10
boolean RADIO_NO = 0; //SET THIS TO 0 or 1 for 1st or 2nd radio
RF24 radio(48,49);
/***************************************************************/
// Topology
// Radio pipe addresses for the 2 nodes to communicate.
const uint64_t pipes[2] = { 0xABCDABCD71LL, 0x544d52687CLL };
const uint64_t pipes[2] = { 0xABCDABCD71LL, 0x544d52687CLL }; // Radio pipe addresses for the 2 nodes to communicate.
// Role management
// Set up role. This sketch uses the same software for all the nodes
// in this system. Doing so greatly simplifies testing.
byte data[32]; //Data buffer for testing data transfer speeds
// The various roles supported by this sketch
typedef enum { role_TX = 1, role_RX } role_e;
// The debug-friendly names of those roles
const char* role_friendly_name[] = { "invalid", "Ping out", "Pong back"};
//Set this to determine the default role of the current running sketch
role_e role = role_RX;
//Data buffer for testing data transfer speeds
byte data[32];
//Counter and timer for keeping track transfer info
unsigned long counter, rxTimer;
unsigned long counter, rxTimer; //Counter and timer for keeping track transfer info
float startTime, stopTime;
bool TX=1,RX=0,role=0;
void setup(void)
{
void setup(void) {
Serial.begin(57600);
printf_begin();
printf("\n\rRF24/examples/GettingStarted/\n\r");
printf("ROLE: %s\n\r",role_friendly_name[role]);
printf("*** PRESS 'T' to begin transmitting to the other node\n\r");
radio.begin(); // Setup and configure rf radio
radio.begin(); // Setup and configure rf radio
radio.setChannel(1);
radio.setPALevel(RF24_PA_MAX);
radio.setAutoAck(1); // Ensure autoACK is enabled
radio.setRetries(2,3); // Optionally, increase the delay between retries & # of retries
//radio.disableCRC();
radio.setAutoAck(1); // Ensure autoACK is enabled
radio.setRetries(1,1); // Optionally, increase the delay between retries & # of retries
radio.setCRCLength(RF24_CRC_8);
radio.openWritingPipe(pipes[1]);
radio.openReadingPipe(1,pipes[0]);
if(RADIO_NO){ //Lets the two radios choose the correct pipes depending on user selection
radio.openWritingPipe(pipes[0]);
radio.openReadingPipe(1,pipes[1]);
}else{
radio.openWritingPipe(pipes[1]);
radio.openReadingPipe(1,pipes[0]);
}
radio.startListening(); // Start listening
radio.printDetails(); // Dump the configuration of the rf unit for debugging
printf("\n\rRF24/examples/Transfer Rates/\n\r");
printf("*** PRESS 'T' to begin transmitting to the other node\n\r");
randomSeed(analogRead(0)); //Seed for random number generation
for(int i=0; i<32; i++){
data[i] = random(255); //Load the buffer with random data
}
radio.powerUp();
radio.powerUp(); //Power up the radio
}
void loop(void){
//TX with pre-blocking writes
if(role == role_TX){
if(role == TX){
delay(1500);
printf("Initiating Basic Data Transfer\n\r");
float cycles = 10000;
float cycles = 1000; //Change this to a higher or lower number.
startTime = millis();
for(int i=0; i<cycles; i++){
if(!radio.writeFast(&data,32)){
counter++;
for(int i=0; i<cycles; i++){ //Loop through a number of cycles
data[0] = i; //Change the first byte of the payload for identification
if(!radio.writeFast(&data,32)){ //Write to the FIFO buffers
counter++; //Keep count of failed payloads
}
}
stopTime = millis();
while(!radio.txStandBy()){ }
while(!radio.txStandBy()){ } //This should be called to wait for completion and put the radio in standby mode after transmission
float numBytes = cycles * 32;
float rate = numBytes / (stopTime - startTime) / cycles;
printf("Transfer complete at "); Serial.print(rate); printf(" KB/s \n\r");
printf("%d of ",counter); Serial.print(cycles); printf(" Packets Failed to Send\n\r");
counter = 0;
printf("Transfer complete at "); Serial.print(rate); printf(" KB/s \n\r");
printf("%d of ",counter); Serial.print(cycles); printf(" Packets Failed to Send\n\r");
counter = 0;
}
if(role == role_RX){
if(role == RX){
while(radio.available()){
radio.read(&data,32);
counter++;
@@ -130,9 +117,7 @@ void loop(void){
printf("Payload Count: %d \n\r", counter);
counter = 0;
}
}
//
// Change roles
//
@@ -140,24 +125,18 @@ void loop(void){
if ( Serial.available() )
{
char c = toupper(Serial.read());
if ( c == 'T' && role == role_RX )
if ( c == 'T' && role == RX )
{
printf("*** CHANGING TO TRANSMIT ROLE -- PRESS 'R' TO SWITCH BACK\n\r");
radio.stopListening();
role = role_TX; // Become the primary transmitter (ping out)
//radio.openWritingPipe(pipes[0]);
//radio.openReadingPipe(1,pipes[1]);
role = TX; // Become the primary transmitter (ping out)
}
else if ( c == 'R' && role == role_TX )
else if ( c == 'R' && role == TX )
{
radio.startListening();
printf("*** CHANGING TO RECEIVE ROLE -- PRESS 'T' TO SWITCH BACK\n\r");
role = role_RX; // Become the primary receiver (pong back)
//radio.openWritingPipe(pipes[1]);
//radio.openReadingPipe(1,pipes[0]);
printf("*** CHANGING TO RECEIVE ROLE -- PRESS 'T' TO SWITCH BACK\n\r");
role = RX; // Become the primary receiver (pong back)
}
}
}
// vim:cin:ai:sts=2 sw=2 ft=cpp
// vim:cin:ai:sts=2 sw=2 ft=cpp