C:ifying continues..
This commit is contained in:
Henrik Ekblad
@@ -22,33 +22,53 @@
|
||||
#define MyConfig_h
|
||||
#include <stdint.h>
|
||||
|
||||
// Enable debug flag for debug prints. This will add a lot to the size of the final sketch but good
|
||||
// to see what is actually is happening when developing
|
||||
// Enables this in sketch to show debug prints. This option will add a lot to the size of the
|
||||
// final sketch but is helpful to see what is actually is happening during development
|
||||
//#define MY_DEBUG
|
||||
|
||||
// Enable this line, If you are using TX(1), RX(0) as normal I/O pin
|
||||
// #define MY_DISABLED_SERIAL
|
||||
// Enable this in sketch if you want to use TX(1), RX(0) as normal I/O pin
|
||||
//#define MY_DISABLED_SERIAL
|
||||
|
||||
// Turn off debug if serial pins is used for other stuff
|
||||
#ifdef MY_DISABLED_SERIAL
|
||||
#undef MY_DEBUG
|
||||
#endif
|
||||
|
||||
// Serial output baud rate (for debug prints and serial gateway)
|
||||
#ifndef MY_BAUD_RATE
|
||||
#define MY_BAUD_RATE 115200
|
||||
#endif
|
||||
|
||||
// Node id defaults to AUTO (tries to fetch id from controller)
|
||||
#ifndef MY_NODE_ID
|
||||
#define MY_NODE_ID AUTO
|
||||
#endif
|
||||
|
||||
// Node parent defaults to AUTO (tries to find a parent automatically)
|
||||
#ifndef MY_PARENT_NODE_ID
|
||||
#define MY_PARENT_NODE_ID AUTO
|
||||
#endif
|
||||
|
||||
// Enables repeater functionality (relays messages from other nodes)
|
||||
// #define MY_REPEATER_FEATURE
|
||||
|
||||
/**********************************
|
||||
* Over the air firmware updates
|
||||
***********************************/
|
||||
|
||||
// The following define enables the safe over-the-air firmware update feature
|
||||
// which requires external flash and the DualOptiBoot bootloader.
|
||||
// Enable MY_OTA_FIRMWARE_FEATURE in sketch to allow safe over-the-air firmware updates.
|
||||
// This feature requires external flash and the DualOptiBoot bootloader.
|
||||
// Note: You can still have OTA FW updates without external flash but it
|
||||
// requires the MYSBootloader and disabled MY_OTA_FIRMWARE_FEATURE
|
||||
//#define MY_OTA_FIRMWARE_FEATURE
|
||||
|
||||
// Slave select pin for external flash
|
||||
#ifdef MY_OTA_FLASH_SS
|
||||
#ifndef MY_OTA_FLASH_SS
|
||||
#define MY_OTA_FLASH_SS 8
|
||||
#endif
|
||||
|
||||
// Flash jdecid
|
||||
#ifdef MY_OTA_FLASH_JDECID
|
||||
#ifndef MY_OTA_FLASH_JDECID
|
||||
#define MY_OTA_FLASH_JDECID 0x1F65
|
||||
#endif
|
||||
|
||||
@@ -112,8 +132,10 @@
|
||||
/**********************************
|
||||
* Message Signing Settings
|
||||
***********************************/
|
||||
// Disable to completely disable signing functionality in library
|
||||
//#define MY_SIGNING_FEATURE
|
||||
|
||||
// Enable one of these in sketch to use signing functionality
|
||||
//#define MY_SIGNING_ATSHA204
|
||||
//#define MY_SIGNING_SOFT
|
||||
|
||||
// Define a suitable timeout for a signature verification session
|
||||
// Consider the turn-around from a nonce being generated to a signed message being received
|
||||
@@ -151,18 +173,30 @@
|
||||
/**********************************
|
||||
* NRF24L01 Driver Defaults
|
||||
***********************************/
|
||||
#define RF24_CE_PIN 9
|
||||
#define RF24_CS_PIN 10
|
||||
#define RF24_PA_LEVEL RF24_PA_MAX
|
||||
#define RF24_PA_LEVEL_GW RF24_PA_LOW
|
||||
// RF channel for the sensor net, 0-127
|
||||
#define RF24_CHANNEL 76
|
||||
//RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
|
||||
#define RF24_DATARATE RF24_250KBPS
|
||||
// This is also act as base value for sensor nodeId addresses. Change this (or channel) if you have more than one sensor network.
|
||||
#define RF24_BASE_RADIO_ID ((uint64_t)0xA8A8E1FC00LL)
|
||||
#ifndef MY_RF24_CE_PIN
|
||||
#define MY_RF24_CE_PIN 9
|
||||
#endif
|
||||
#ifndef MY_RF24_CS_PIN
|
||||
#define MY_RF24_CS_PIN 10
|
||||
#endif
|
||||
|
||||
// Enable SOFTSPI for NRF24L01 when using the W5100 Ethernet module
|
||||
#ifndef MY_RF24_PA_LEVEL
|
||||
#define MY_RF24_PA_LEVEL RF24_PA_MAX
|
||||
#endif
|
||||
// RF channel for the sensor net, 0-127
|
||||
#ifndef MY_RF24_CHANNEL
|
||||
#define MY_RF24_CHANNEL 76
|
||||
#endif
|
||||
//RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
|
||||
#ifndef MY_RF24_DATARATE
|
||||
#define MY_RF24_DATARATE RF24_250KBPS
|
||||
#endif
|
||||
// This is also act as base value for sensor nodeId addresses. Change this (or channel) if you have more than one sensor network.
|
||||
#ifndef MY_RF24_BASE_RADIO_ID
|
||||
#define MY_RF24_BASE_RADIO_ID ((uint64_t)0xA8A8E1FC00LL)
|
||||
#endif
|
||||
|
||||
// Enable SOFTSPI for NRF24L01, useful for the W5100 Ethernet module
|
||||
//#define MY_SOFTSPI
|
||||
|
||||
#ifndef MY_SOFT_SPI_SCK_PIN
|
||||
@@ -186,6 +220,11 @@
|
||||
//#define MY_RFM69_FREQUENCY RF69_915MHZ
|
||||
#endif
|
||||
|
||||
// Enable this if you're running the RFM69HW model
|
||||
#ifndef MY_IS_RFM69HW
|
||||
#define MY_IS_RFM69HW false
|
||||
#endif
|
||||
|
||||
// Default network id. Use the same for all nodes that will talk to each other
|
||||
#ifndef MY_RFM69_NETWORKID
|
||||
#define MY_RFM69_NETWORKID 100
|
||||
@@ -210,9 +249,16 @@
|
||||
* Gateway Transport Ethernet Defaults
|
||||
***************************************/
|
||||
// Enable to use DHCP for getting IP address. If not defined, static IP is expected
|
||||
//#define IP_ADDRESS_DHCP
|
||||
//#define MY_IP_ADDRESS_VIA_DHCP
|
||||
|
||||
#ifndef MY_IP_RENEWAL_INTERVAL
|
||||
#define MY_IP_RENEWAL_INTERVAL 60000
|
||||
#endif
|
||||
|
||||
#ifndef MY_MAC_ADDRESS
|
||||
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
|
||||
#endif
|
||||
// Enable to use UDP instead of plain Ethernet
|
||||
#define MY_USE_UDP
|
||||
//#define MY_USE_UDP
|
||||
|
||||
#endif
|
||||
|
||||
Reference in New Issue
Block a user