Rename example sketch
This commit is contained in:
Henrik Ekblad
@@ -0,0 +1,309 @@
|
||||
// Default sensor sketch for Sensebender Micro module
|
||||
// Act as a temperature / humidity sensor by default.
|
||||
//
|
||||
// If A0 is held low while powering on, it will enter testmode, which verifies all on-board peripherals
|
||||
//
|
||||
// Battery voltage is repported as child sensorId 199, as well as battery percentage (Internal message)
|
||||
|
||||
|
||||
#include <MySensor.h>
|
||||
#include <Wire.h>
|
||||
#include <SI7021.h>
|
||||
#include <SPI.h>
|
||||
#include <SPIFlash.h>
|
||||
#include <EEPROM.h>
|
||||
#include <sha204_lib_return_codes.h>
|
||||
#include <sha204_library.h>
|
||||
|
||||
// Define a static node address, remove if you want auto address assignment
|
||||
//#define NODE_ADDRESS 3
|
||||
|
||||
#define RELEASE "1.1"
|
||||
|
||||
// Child sensor ID's
|
||||
#define CHILD_ID_TEMP 1
|
||||
#define CHILD_ID_HUM 2
|
||||
#define CHILD_ID_BATT 199
|
||||
|
||||
// How many milli seconds between each measurement
|
||||
#define MEASURE_INTERVAL 60000
|
||||
|
||||
// FORCE_TRANSMIT_INTERVAL, this number of times of wakeup, the sensor is forced to report all values to the controller
|
||||
#define FORCE_TRANSMIT_INTERVAL 30
|
||||
|
||||
// When MEASURE_INTERVAL is 60000 and FORCE_TRANSMIT_INTERVAL is 30, we force a transmission every 30 minutes.
|
||||
// Between the forced transmissions a tranmission will only occur if the measured value differs from the previous measurement
|
||||
|
||||
//Pin definitions
|
||||
#define TEST_PIN A0
|
||||
#define LED_PIN A2
|
||||
#define ATSHA204_PIN 17 // A3
|
||||
|
||||
const int sha204Pin = ATSHA204_PIN;
|
||||
atsha204Class sha204(sha204Pin);
|
||||
|
||||
SI7021 humiditySensor;
|
||||
SPIFlash flash(8, 0x1F65);
|
||||
|
||||
MySensor gw;
|
||||
|
||||
// Sensor messages
|
||||
MyMessage msgHum(CHILD_ID_HUM, V_HUM);
|
||||
MyMessage msgTemp(CHILD_ID_TEMP, V_TEMP);
|
||||
MyMessage msgBattery(CHILD_ID_BATT, V_VOLTAGE);
|
||||
|
||||
// Global settings
|
||||
int measureCount = 0;
|
||||
boolean isMetric = true;
|
||||
|
||||
// Storage of old measurements
|
||||
float lastTemperature = -100;
|
||||
int lastHumidity = -100;
|
||||
long lastBattery = -100;
|
||||
|
||||
bool highfreq = true;
|
||||
|
||||
void setup() {
|
||||
|
||||
pinMode(LED_PIN, OUTPUT);
|
||||
digitalWrite(LED_PIN, LOW);
|
||||
|
||||
Serial.begin(115200);
|
||||
Serial.print(F("Sensebender Micro FW "));
|
||||
Serial.print(RELEASE);
|
||||
Serial.flush();
|
||||
|
||||
// First check if we should boot into test mode
|
||||
|
||||
pinMode(TEST_PIN,INPUT);
|
||||
digitalWrite(TEST_PIN, HIGH); // Enable pullup
|
||||
if (!digitalRead(TEST_PIN)) testMode();
|
||||
|
||||
digitalWrite(TEST_PIN,LOW);
|
||||
digitalWrite(LED_PIN, HIGH);
|
||||
|
||||
#ifdef NODE_ADDRESS
|
||||
gw.begin(NULL, NODE_ADDRESS, false);
|
||||
#else
|
||||
gw.begin(NULL,AUTO,false);
|
||||
#endif
|
||||
|
||||
digitalWrite(LED_PIN, LOW);
|
||||
|
||||
humiditySensor.begin();
|
||||
Serial.flush();
|
||||
Serial.println(F(" - Online!"));
|
||||
gw.sendSketchInfo("Sensebender Micro", RELEASE);
|
||||
|
||||
gw.present(CHILD_ID_TEMP,S_TEMP);
|
||||
gw.present(CHILD_ID_HUM,S_HUM);
|
||||
|
||||
isMetric = gw.getConfig().isMetric;
|
||||
Serial.print("isMetric: "); Serial.println(isMetric);
|
||||
|
||||
}
|
||||
|
||||
|
||||
// Main loop function
|
||||
void loop() {
|
||||
measureCount ++;
|
||||
bool forceTransmit = false;
|
||||
|
||||
// When we wake up the 5th time after power on, switch to 1Mhz clock
|
||||
// This allows us to print debug messages on startup (as serial port is dependend on oscilator settings).
|
||||
if ((measureCount == 5) && highfreq) switchClock(1<<CLKPS2); // Switch to 1Mhz for the reminder of the sketch, save power.
|
||||
|
||||
if (measureCount > FORCE_TRANSMIT_INTERVAL) { // force a transmission
|
||||
forceTransmit = true;
|
||||
measureCount = 0;
|
||||
}
|
||||
|
||||
gw.process();
|
||||
sendBattLevel(forceTransmit);
|
||||
sendTempHumidityMeasurements(forceTransmit);
|
||||
|
||||
gw.sleep(MEASURE_INTERVAL);
|
||||
}
|
||||
|
||||
/*
|
||||
* Sends temperature and humidity from Si7021 sensor
|
||||
*
|
||||
* Parameters
|
||||
* - force : Forces transmission of a value (even if it's the same as previous measurement)
|
||||
*/
|
||||
void sendTempHumidityMeasurements(bool force)
|
||||
{
|
||||
if (force) {
|
||||
lastHumidity = -100;
|
||||
lastTemperature = -100;
|
||||
}
|
||||
|
||||
si7021_env data = humiditySensor.getHumidityAndTemperature();
|
||||
|
||||
float temperature = (isMetric ? data.celsiusHundredths : data.fahrenheitHundredths) / 100.0;
|
||||
|
||||
int humidity = data.humidityPercent;
|
||||
|
||||
if ((lastTemperature != temperature) | (lastHumidity != humidity)) {
|
||||
Serial.print("T: ");Serial.println(temperature);
|
||||
Serial.print("H: ");Serial.println(humidity);
|
||||
|
||||
gw.send(msgTemp.set(temperature,1));
|
||||
gw.send(msgHum.set(humidity));
|
||||
lastTemperature = temperature;
|
||||
lastHumidity = humidity;
|
||||
}
|
||||
}
|
||||
|
||||
/*
|
||||
* Sends battery information (both voltage, and battery percentage)
|
||||
*
|
||||
* Parameters
|
||||
* - force : Forces transmission of a value
|
||||
*/
|
||||
void sendBattLevel(bool force)
|
||||
{
|
||||
if (force) lastBattery = -1;
|
||||
long vcc = readVcc();
|
||||
if (vcc != lastBattery) {
|
||||
lastBattery = vcc;
|
||||
// Calculate percentage
|
||||
|
||||
vcc = vcc - 1900; // subtract 1.9V from vcc, as this is the lowest voltage we will operate at
|
||||
|
||||
long percent = vcc / 14.0;
|
||||
gw.sendBatteryLevel(percent);
|
||||
}
|
||||
}
|
||||
|
||||
long readVcc() {
|
||||
// Read 1.1V reference against AVcc
|
||||
// set the reference to Vcc and the measurement to the internal 1.1V reference
|
||||
#if defined(__AVR_ATmega32U4__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
|
||||
ADMUX = _BV(REFS0) | _BV(MUX4) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);
|
||||
#elif defined (__AVR_ATtiny24__) || defined(__AVR_ATtiny44__) || defined(__AVR_ATtiny84__)
|
||||
ADMUX = _BV(MUX5) | _BV(MUX0);
|
||||
#elif defined (__AVR_ATtiny25__) || defined(__AVR_ATtiny45__) || defined(__AVR_ATtiny85__)
|
||||
ADcdMUX = _BV(MUX3) | _BV(MUX2);
|
||||
#else
|
||||
ADMUX = _BV(REFS0) | _BV(MUX3) | _BV(MUX2) | _BV(MUX1);
|
||||
#endif
|
||||
|
||||
delay(2); // Wait for Vref to settle
|
||||
ADCSRA |= _BV(ADSC); // Start conversion
|
||||
while (bit_is_set(ADCSRA,ADSC)); // measuring
|
||||
|
||||
uint8_t low = ADCL; // must read ADCL first - it then locks ADCH
|
||||
uint8_t high = ADCH; // unlocks both
|
||||
|
||||
long result = (high<<8) | low;
|
||||
|
||||
result = 1125300L / result; // Calculate Vcc (in mV); 1125300 = 1.1*1023*1000
|
||||
return result; // Vcc in millivolts
|
||||
}
|
||||
|
||||
void switchClock(unsigned char clk)
|
||||
{
|
||||
cli();
|
||||
|
||||
CLKPR = 1<<CLKPCE; // Set CLKPCE to enable clk switching
|
||||
CLKPR = clk;
|
||||
sei();
|
||||
highfreq = false;
|
||||
}
|
||||
|
||||
|
||||
// Verify all peripherals, and signal via the LED if any problems.
|
||||
void testMode()
|
||||
{
|
||||
uint8_t rx_buffer[SHA204_RSP_SIZE_MAX];
|
||||
uint8_t ret_code;
|
||||
byte tests = 0;
|
||||
|
||||
digitalWrite(LED_PIN, HIGH); // Turn on LED.
|
||||
Serial.println(F(" - TestMode"));
|
||||
Serial.println(F("Testing peripherals!"));
|
||||
Serial.flush();
|
||||
Serial.print(F("-> SI7021 : "));
|
||||
Serial.flush();
|
||||
|
||||
if (humiditySensor.begin())
|
||||
{
|
||||
Serial.println(F("ok!"));
|
||||
tests ++;
|
||||
}
|
||||
else
|
||||
{
|
||||
Serial.println(F("failed!"));
|
||||
}
|
||||
Serial.flush();
|
||||
|
||||
Serial.print(F("-> Flash : "));
|
||||
Serial.flush();
|
||||
if (flash.initialize())
|
||||
{
|
||||
Serial.println(F("ok!"));
|
||||
tests ++;
|
||||
}
|
||||
else
|
||||
{
|
||||
Serial.println(F("failed!"));
|
||||
}
|
||||
Serial.flush();
|
||||
|
||||
|
||||
Serial.print(F("-> SHA204 : "));
|
||||
ret_code = sha204.sha204c_wakeup(rx_buffer);
|
||||
Serial.flush();
|
||||
if (ret_code != SHA204_SUCCESS)
|
||||
{
|
||||
Serial.print(F("Failed to wake device. Response: ")); Serial.println(ret_code, HEX);
|
||||
}
|
||||
Serial.flush();
|
||||
if (ret_code == SHA204_SUCCESS)
|
||||
{
|
||||
ret_code = sha204.getSerialNumber(rx_buffer);
|
||||
if (ret_code != SHA204_SUCCESS)
|
||||
{
|
||||
Serial.print(F("Failed to obtain device serial number. Response: ")); Serial.println(ret_code, HEX);
|
||||
}
|
||||
else
|
||||
{
|
||||
Serial.print(F("Ok (serial : "));
|
||||
for (int i=0; i<9; i++)
|
||||
{
|
||||
if (rx_buffer[i] < 0x10)
|
||||
{
|
||||
Serial.print('0'); // Because Serial.print does not 0-pad HEX
|
||||
}
|
||||
Serial.print(rx_buffer[i], HEX);
|
||||
}
|
||||
Serial.println(")");
|
||||
tests ++;
|
||||
}
|
||||
|
||||
}
|
||||
Serial.flush();
|
||||
|
||||
Serial.println(F("Test finished"));
|
||||
|
||||
if (tests == 3)
|
||||
{
|
||||
Serial.println(F("Selftest ok!"));
|
||||
while (1) // Blink OK pattern!
|
||||
{
|
||||
digitalWrite(LED_PIN, HIGH);
|
||||
delay(200);
|
||||
digitalWrite(LED_PIN, LOW);
|
||||
delay(200);
|
||||
}
|
||||
}
|
||||
else
|
||||
{
|
||||
Serial.println(F("----> Selftest failed!"));
|
||||
while (1) // Blink FAILED pattern! Rappidly blinking..
|
||||
{
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
Reference in New Issue
Block a user