/* * The MySensors Arduino library handles the wireless radio link and protocol * between your home built sensors/actuators and HA controller of choice. * The sensors forms a self healing radio network with optional repeaters. Each * repeater and gateway builds a routing tables in RAM or EEPROM which keeps track of the * network topology allowing messages to be routed to nodes. * * Created by Henrik Ekblad * Copyright (C) 2013-2015 Sensnology AB * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors * * Documentation: http://www.mysensors.org * Support Forum: http://forum.mysensors.org * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License * version 2 as published by the Free Software Foundation. */ /** * @file MyConfig.h * * MySensors specific configurations */ #ifndef MyConfig_h #define MyConfig_h #include /********************************** * Serial and debug options ***********************************/ // Enable MY_DEBUG in sketch to show debug prints. This option will add a lot to the size of the // final sketch but is helpful to see what is actually is happening during development //#define MY_DEBUG // Enable MY_SPECIAL_DEBUG in sketch to activate I_DEBUG messages if MY_DEBUG is disabled. // I_DEBUG requests are: // R: routing info (only repeaters): received msg XXYY (as stream), where XX is the node and YY the routing node // V: CPU voltage // F: CPU frequency // M: free memory // E: clear MySensors EEPROM area and reboot (i.e. "factory" reset) //#define MY_SPECIAL_DEBUG // Enable MY_DEBUG_VERBOSE_SIGNING flag for verbose debug prints related to signing. // Requires DEBUG to be enabled. // This will add even more to the size of the final sketch! //#define MY_DEBUG_VERBOSE_SIGNING // Enable this in sketch if you want to use TX(1), RX(0) as normal I/O pin //#define MY_DISABLED_SERIAL // Enable MY_CORE_ONLY flag if you want to use core functions without loading the framework //#define MY_CORE_ONLY // Turn off debug if serial pins is used for other stuff #ifdef MY_DISABLED_SERIAL #undef MY_DEBUG #endif /** * @def MY_BAUD_RATE * @brief Serial output baud rate (debug prints and serial gateway speed). */ #ifndef MY_BAUD_RATE #define MY_BAUD_RATE 115200 #endif // Disables over-the-air reset of node //#define MY_DISABLE_REMOTE_RESET /********************************** * Radio selection and node config ***********************************/ // Selecting uplink transport layer is optional (for a gateway node). //#define MY_RADIO_NRF24 //#define MY_RADIO_RFM69 //#define MY_RS485 /** * @def MY_RAM_ROUTING_TABLE_FEATURE * @brief If enabled, the routing table is kept in RAM (if memory allows) and saved in regular intervals. * note: AVR has limited memory, use with care */ #define MY_RAM_ROUTING_TABLE_FEATURE /** * @def MY_ROUTING_TABLE_SAVE_INTERVAL_MS * @brief Interval to dump content of routing table to eeprom */ #ifndef MY_ROUTING_TABLE_SAVE_INTERVAL_MS #define MY_ROUTING_TABLE_SAVE_INTERVAL_MS (10*60*1000ul) #endif /** * @def MY_TRANSPORT_SANITY_CHECK * @brief If enabled, node will check transport in regular intervals to detect HW issues and re-initialize in case of failure. * This feature is enabled for all repeater nodes (incl. GW) */ //#define MY_TRANSPORT_SANITY_CHECK /** * @def MY_TRANSPORT_SANITY_CHECK_INTERVAL_MS * @brief Interval (in ms) of transport sanity checks */ #ifndef MY_TRANSPORT_SANITY_CHECK_INTERVAL_MS #define MY_TRANSPORT_SANITY_CHECK_INTERVAL_MS (60*1000ul) #endif /** * @def MY_TRANSPORT_DISCOVERY_INTERVAL_MS * @brief This is a gateway-only feature: Interval (in ms) to issue network discovery checks */ #ifndef MY_TRANSPORT_DISCOVERY_INTERVAL_MS #define MY_TRANSPORT_DISCOVERY_INTERVAL_MS (10*60*1000ul) #endif /** *@def MY_TRANSPORT_UPLINK_CHECK_DISABLED *@brief If set, uplink check to GW is disabled during transport initialisation */ //#define MY_TRANSPORT_UPLINK_CHECK_DISABLED /** *@def MY_TRANSPORT_DONT_CARE_MODE *@brief If set, transport traffic is unmonitored and GW connection is optional */ //#define MY_TRANSPORT_DONT_CARE_MODE /** *@def MY_TRANSPORT_MAX_TX_FAILURES *@brief Set to override max. consecutive TX failures until SNP is initiated */ //#define MY_TRANSPORT_MAX_TX_FAILURES (10u) /** * @def MY_REGISTRATION_FEATURE * @brief If enabled, node has to register to gateway/controller before allowed to send sensor data. */ #define MY_REGISTRATION_FEATURE /** * @def MY_REGISTRATION_RETRIES * @brief Number of registration retries if no reply received from GW/controller */ #ifndef MY_REGISTRATION_RETRIES #define MY_REGISTRATION_RETRIES (3u) #endif /** * @def MY_REGISTRATION_DEFAULT * @brief Node registration default - this applies if no registration response is received from controller */ #define MY_REGISTRATION_DEFAULT true /** * @def MY_REGISTRATION_CONTROLLER * @brief If enabled, node registration request has to be handled by controller */ // #define MY_REGISTRATION_CONTROLLER /** * @def MY_CORE_COMPATIBILITY_CHECK * @brief If enabled, library compatibility is checked during node registration. Incompatible libraries are unable to send sensor data. */ #define MY_CORE_COMPATIBILITY_CHECK /** * @def MY_NODE_ID * @brief Node id defaults to AUTO (tries to fetch id from controller). */ #ifndef MY_NODE_ID #define MY_NODE_ID AUTO #endif /** * @def MY_PARENT_NODE_ID * @brief Node parent defaults to AUTO (tries to find a parent automatically). */ #ifndef MY_PARENT_NODE_ID #define MY_PARENT_NODE_ID AUTO #endif /** * @def MY_PARENT_NODE_IS_STATIC * @brief Enable MY_PARENT_NODE_IS_STATIC to disable fall back if parent node fails */ //#define MY_PARENT_NODE_IS_STATIC /** * @def MY_REPEATER_FEATURE * @brief Enables repeater functionality (relays messages from other nodes) */ //#define MY_REPEATER_FEATURE /** * @def MY_SLEEP_TRANSPORT_RECONNECT_TIMEOUT_MS * @brief Timeout (in ms) to re-establish link if node is send to sleep and transport is not ready. */ #ifndef MY_SLEEP_TRANSPORT_RECONNECT_TIMEOUT_MS #define MY_SLEEP_TRANSPORT_RECONNECT_TIMEOUT_MS (10*1000ul) #endif /** * @def MY_SMART_SLEEP_WAIT_DURATION_MS * @brief The wait period (in ms) before going to sleep when using smartSleep-functions. * * This period has to be long enough for controller to be able to send out * potential buffered messages. */ #ifndef MY_SMART_SLEEP_WAIT_DURATION_MS #define MY_SMART_SLEEP_WAIT_DURATION_MS (500ul) #endif /********************************** * Over the air firmware updates ***********************************/ // Enable MY_OTA_FIRMWARE_FEATURE in sketch to allow safe over-the-air firmware updates. // This feature requires external flash and the DualOptiBoot boot-loader. // Note: You can still have OTA FW updates without external flash but it // requires the MYSBootloader and disabled MY_OTA_FIRMWARE_FEATURE //#define MY_OTA_FIRMWARE_FEATURE /** * @def MY_OTA_FLASH_SS * @brief Slave select pin for external flash. */ #ifndef MY_OTA_FLASH_SS #define MY_OTA_FLASH_SS 8 #endif /** * @def MY_OTA_FLASH_JDECID * @brief Flash jdecid. */ #ifndef MY_OTA_FLASH_JDECID #define MY_OTA_FLASH_JDECID 0x1F65 #endif /********************************** * Gateway config ***********************************/ /** * @def MY_GATEWAY_MAX_RECEIVE_LENGTH * @brief Max buffersize needed for messages coming from controller. */ #ifndef MY_GATEWAY_MAX_RECEIVE_LENGTH #define MY_GATEWAY_MAX_RECEIVE_LENGTH (100u) #endif /** * @def MY_GATEWAY_MAX_SEND_LENGTH * @brief Max buffer size when sending messages. */ #ifndef MY_GATEWAY_MAX_SEND_LENGTH #define MY_GATEWAY_MAX_SEND_LENGTH (120u) #endif /** * @def MY_GATEWAY_MAX_CLIENTS * @brief Max number of parallel clients (sever mode). */ #ifndef MY_GATEWAY_MAX_CLIENTS #define MY_GATEWAY_MAX_CLIENTS (1u) #endif /********************************** * Information LEDs blinking ***********************************/ // If one of the following is defined here, or in the sketch, the pin will be used for the // corresponding led function. // They have to be enabled here (or in your sketch). Replace x with the pin number you have the LED on. // // NOTE!! that on some platforms (for example sensebender GW) the hardware variant can enable LEDs by default, // These defaults can be overridden by defining one of these. //#define MY_DEFAULT_ERR_LED_PIN x //#define MY_DEFAULT_TX_LED_PIN x //#define MY_DEFAULT_RX_LED_PIN x // The following setting allows you to inverse the LED blinking // When MY_WITH_LEDS_BLINKING_INVERSE is enabled LEDSs are normally turned on and switches // off when blinking //#define MY_WITH_LEDS_BLINKING_INVERSE /********************************************** * Gateway inclusion button/mode configuration **********************************************/ // Enabled inclusion mode feature //#define MY_INCLUSION_MODE_FEATURE // Enables inclusion-mode button feature on the gateway device //#define MY_INCLUSION_BUTTON_FEATURE // Disable inclusion mode button if inclusion mode feature is not enabled #ifndef MY_INCLUSION_MODE_FEATURE #undef MY_INCLUSION_BUTTON_FEATURE #endif /** * @def MY_INCLUSION_MODE_BUTTON_PIN * @brief The default input pin used for the inclusion mode button. */ #ifndef MY_INCLUSION_MODE_BUTTON_PIN #if defined(ARDUINO_ARCH_ESP8266) #define MY_INCLUSION_MODE_BUTTON_PIN 5 #else #define MY_INCLUSION_MODE_BUTTON_PIN 3 #endif #endif /** * @def MY_INCLUSION_MODE_DURATION * @brief Number of seconds (default one minute) inclusion mode should be enabled. */ #ifndef MY_INCLUSION_MODE_DURATION #define MY_INCLUSION_MODE_DURATION 60 #endif /** * @def MY_INCLUSION_BUTTON_PRESSED * @brief The logical level indicating a pressed inclusion mode button. */ #if defined(MY_INCLUSION_BUTTON_EXTERNAL_PULLUP) #define MY_INCLUSION_BUTTON_PRESSED HIGH #else #define MY_INCLUSION_BUTTON_PRESSED LOW #endif /********************************** * Message Signing Settings ***********************************/ /** * @def MY_SIGNING_ATSHA204 * @brief Enables HW backed signing functionality in library. * * For any signing related functionality to be included, this define or @ref MY_SIGNING_SOFT has to be enabled. */ //#define MY_SIGNING_ATSHA204 /** * @def MY_SIGNING_SOFT * @brief Enables SW backed signing functionality in library. * * For any signing related functionality to be included, this define or @ref MY_SIGNING_ATSHA204 has to be enabled. */ //#define MY_SIGNING_SOFT /** * @def MY_SIGNING_REQUEST_SIGNATURES * @brief Enable this to inform gateway to sign all messages sent to this node. * * If used for a gateway, gateway will only request signatures from nodes that in turn * request signatures from gateway. */ //#define MY_SIGNING_REQUEST_SIGNATURES /** * @def MY_SIGNING_GW_REQUEST_SIGNATURES_FROM_ALL * @brief Enable this to have gateway require all nodes in the network to sign messages sent to it. @ref MY_SIGNING_REQUEST_SIGNATURES must also be set. * * Use this for maximum security, but be aware that every single node will have to be personalized before they can be used. * Note that if this is enabled, and whitelisting is also enabled, whitelisting will also be in effect for all nodes. */ //#define MY_SIGNING_GW_REQUEST_SIGNATURES_FROM_ALL /** * @def MY_VERIFICATION_TIMEOUT_MS * @brief Define a suitable timeout for a signature verification session * * Consider the turnaround from a nonce being generated to a signed message being received * which might vary, especially in networks with many hops. 5s ought to be enough for anyone. */ #ifndef MY_VERIFICATION_TIMEOUT_MS #define MY_VERIFICATION_TIMEOUT_MS 5000 #endif /** * @def MY_SIGNING_NODE_WHITELISTING * @brief Enable to turn on whitelisting * * When enabled, a signing node will salt the signature with it's unique signature and nodeId.
* The verifying node will look up the sender in a local table of trusted nodes and * do the corresponding salting in order to verify the signature.
* For this reason, if whitelisting is enabled on one of the nodes in a sign-verify pair, both * nodes have to implement whitelisting for this to work.
* Note that a node can still transmit a non-salted message (i.e. have whitelisting disabled) * to a node that has whitelisting enabled (assuming the receiver does not have a matching entry * for the sender in it's whitelist). The whitelist to use is defined as the value of the flag. */ //#define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0x09,0x08,0x07,0x06,0x05,0x04,0x03,0x02,0x01}}} /** * @def MY_SIGNING_ATSHA204_PIN * @brief Atsha204 default pin setting * * Pin where ATSHA204 is attached */ #ifndef MY_SIGNING_ATSHA204_PIN #define MY_SIGNING_ATSHA204_PIN 17 #endif /** * @def MY_SIGNING_SOFT_RANDOMSEED_PIN * @brief Pin used for random generation in soft signing * * Do not connect anything to this when soft signing is enabled */ #ifndef MY_SIGNING_SOFT_RANDOMSEED_PIN #define MY_SIGNING_SOFT_RANDOMSEED_PIN 7 #endif /********************************** * RS485 Driver Defaults ***********************************/ /** * @def MY_RS485_BAUD_RATE * @brief The RS485 BAUD rate. */ #ifndef MY_RS485_BAUD_RATE #define MY_RS485_BAUD_RATE 9600 #endif /** * @def MY_RS485_MAX_MESSAGE_LENGTH * @brief The maximum message length used for RS485. */ #ifndef MY_RS485_MAX_MESSAGE_LENGTH #define MY_RS485_MAX_MESSAGE_LENGTH 40 #endif /** * @def MY_RS485_DE_PIN * @brief RS485 driver enable pin. */ //#define MY_RS485_DE_PIN 2 /** * @def MY_RS485_HWSERIAL * @brief Enable this if RS485 is connected to a hardware serial port. */ //#define MY_RS485_HWSERIAL Serial1 /********************************** * NRF24L01P Driver Defaults ***********************************/ // Enables RF24 encryption (all nodes and gateway must have this enabled, and all must be personalized with the same AES key) //#define MY_RF24_ENABLE_ENCRYPTION /** * @def MY_DEBUG_VERBOSE_RF24 * @brief Enable MY_DEBUG_VERBOSE_RF24 flag for verbose debug prints related to the RF24 driver. Requires DEBUG to be enabled. */ //#define MY_DEBUG_VERBOSE_RF24 /** * @def MY_RF24_SPI_MAX_SPEED * @brief MY_RF24_SPI_MAX_SPEED to overrule default nRF24L01+ SPI speed. */ //#define MY_RF24_SPI_MAX_SPEED 4000000 /** * @def MY_RF24_CE_PIN * @brief Default RF24 chip enable pin setting. Override in sketch if needed. */ #ifndef MY_RF24_CE_PIN #if defined(ARDUINO_ARCH_ESP8266) #define MY_RF24_CE_PIN 4 #elif defined(ARDUINO_ARCH_SAMD) #define MY_RF24_CE_PIN 27 #elif defined(LINUX_ARCH_RASPBERRYPI) #define MY_RF24_CE_PIN 22 #else #define MY_RF24_CE_PIN 9 #endif #endif /** * @def MY_RF24_CS_PIN * @brief Default RF24 chip select pin setting. Override in sketch if needed. */ #ifndef MY_RF24_CS_PIN #if defined(ARDUINO_ARCH_ESP8266) #define MY_RF24_CS_PIN 15 #elif defined(ARDUINO_ARCH_SAMD) #define MY_RF24_CS_PIN 3 #elif defined(LINUX_ARCH_RASPBERRYPI) #define MY_RF24_CS_PIN 24 #else #define MY_RF24_CS_PIN 10 #endif #endif /** * @def MY_RX_MESSAGE_BUFFER_FEATURE * @brief This enabled the receiving buffer feature. * * This feature is currently not supported for RFM69 and RS485, for RF24 MY_RF24_IRQ_PIN has to be defined. */ //#define MY_RX_MESSAGE_BUFFER_FEATURE /** * @def MY_RX_MESSAGE_BUFFER_SIZE * @brief Declare the amount of incoming messages that can be buffered. */ #ifdef MY_RX_MESSAGE_BUFFER_FEATURE #ifndef MY_RX_MESSAGE_BUFFER_SIZE #define MY_RX_MESSAGE_BUFFER_SIZE (20) #endif #endif /** * @def MY_RF24_PA_LEVEL * @brief Default RF24 PA level. Override in sketch if needed. */ #ifndef MY_RF24_PA_LEVEL #define MY_RF24_PA_LEVEL RF24_PA_MAX #endif /** * @def MY_RF24_CHANNEL * @brief RF channel for the sensor net, 0-125. * Frequence: 2400 Mhz - 2525 Mhz Channels: 126 * http://www.mysensors.org/radio/nRF24L01Plus.pdf * 0 => 2400 Mhz (RF24 channel 1) * 1 => 2401 Mhz (RF24 channel 2) * 76 => 2476 Mhz (RF24 channel 77) * 83 => 2483 Mhz (RF24 channel 84) * 124 => 2524 Mhz (RF24 channel 125) * 125 => 2525 Mhz (RF24 channel 126) * In some countries there might be limitations, in Germany for example only the range 2400,0 - 2483,5 Mhz is allowed * http://www.bundesnetzagentur.de/SharedDocs/Downloads/DE/Sachgebiete/Telekommunikation/Unternehmen_Institutionen/Frequenzen/Allgemeinzuteilungen/2013_10_WLAN_2,4GHz_pdf.pdf */ #ifndef MY_RF24_CHANNEL #define MY_RF24_CHANNEL 76 #endif /** * @def MY_RF24_DATARATE * @brief RF24 datarate (RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps or RF24_2MBPS for 2Mbps). */ #ifndef MY_RF24_DATARATE #define MY_RF24_DATARATE RF24_250KBPS #endif /** * @def MY_RF24_BASE_RADIO_ID * @brief RF24 radio network identifier. * * This acts as base value for sensor nodeId addresses. Change this (or channel) if you have more than one sensor network. */ #ifndef MY_RF24_BASE_RADIO_ID #define MY_RF24_BASE_RADIO_ID 0x00,0xFC,0xE1,0xA8,0xA8 #endif /** * @def MY_RF24_ADDR_WIDTH * @brief RF24 address width. * * This defines the width of the base address. */ #ifndef MY_RF24_ADDR_WIDTH #define MY_RF24_ADDR_WIDTH 5 #endif // Enable SOFTSPI for NRF24L01, useful for the W5100 Ethernet module //#define MY_SOFTSPI /** * @def MY_SOFT_SPI_SCK_PIN * @brief Soft SPI SCK pin. */ #ifndef MY_SOFT_SPI_SCK_PIN #define MY_SOFT_SPI_SCK_PIN 14 #endif /** * @def MY_SOFT_SPI_MISO_PIN * @brief Soft SPI MISO pin. */ #ifndef MY_SOFT_SPI_MISO_PIN #define MY_SOFT_SPI_MISO_PIN 16 #endif /** * @def MY_SOFT_SPI_MOSI_PIN * @brief Soft SPI MOSI pin. */ #ifndef MY_SOFT_SPI_MOSI_PIN #define MY_SOFT_SPI_MOSI_PIN 15 #endif /********************************** * RFM69 Driver Defaults ***********************************/ /** * @def MY_RFM69_FREQUENCY * @brief RFM69 frequency to use (RF69_433MHZ for 433MHz, RF69_868MHZ for 868MHz or RF69_915MHZ for 915MHz). * * This must match the hardware version of the RFM69 radio. */ #ifndef MY_RFM69_FREQUENCY #define MY_RFM69_FREQUENCY RF69_868MHZ #endif /** * @def MY_IS_RFM69HW * @brief Enable this if you're running the RFM69HW model. */ //#define MY_IS_RFM69HW /** * @def MY_RFM69HW * @brief Set to true if @ref MY_IS_RFM69HW is set. */ #ifdef MY_IS_RFM69HW #define MY_RFM69HW true #else #define MY_RFM69HW false #endif /** * @def MY_RFM69_NETWORKID * @brief RFM69 Network ID. Use the same for all nodes that will talk to each other. */ #ifndef MY_RFM69_NETWORKID #define MY_RFM69_NETWORKID 100 #endif /** * @def MY_RF69_IRQ_PIN * @brief RF69 IRQ pin. */ #ifndef MY_RF69_IRQ_PIN #define MY_RF69_IRQ_PIN RF69_IRQ_PIN #endif /** * @def MY_RF69_SPI_CS * @brief RF69 SPI chip select pin. */ #ifndef MY_RF69_SPI_CS #define MY_RF69_SPI_CS RF69_SPI_CS #endif /** * @def MY_RF69_IRQ_NUM * @brief RF69 IRQ pin number. */ #ifndef MY_RF69_IRQ_NUM #if defined(ARDUINO_ARCH_ESP8266) #define MY_RF69_IRQ_NUM MY_RF69_IRQ_PIN #else #define MY_RF69_IRQ_NUM RF69_IRQ_NUM #endif #endif // Enables RFM69 encryption (all nodes and gateway must have this enabled, and all must be personalized with the same AES key) //#define MY_RFM69_ENABLE_ENCRYPTION /************************************** * Ethernet Gateway Transport Defaults ***************************************/ // The gateway options available //#define MY_GATEWAY_W5100 //#define MY_GATEWAY_ENC28J60 //#define MY_GATEWAY_ESP8266 //#define MY_GATEWAY_LINUX /** * @def MY_PORT * @brief The Ethernet TCP/UDP port to open on controller or gateway. */ #ifndef MY_PORT #ifdef MY_GATEWAY_MQTT_CLIENT #define MY_PORT 1883 #else #define MY_PORT 5003 #endif #endif // Static ip address of gateway (if this is disabled, DHCP will be used) //#define MY_IP_ADDRESS 192,168,178,66 // Enables UDP mode for Ethernet gateway (W5100) //#define MY_USE_UDP /** * @def MY_IP_RENEWAL_INTERVAL * @brief DHCP, default renewal setting in milliseconds. */ #ifndef MY_IP_RENEWAL_INTERVAL #define MY_IP_RENEWAL_INTERVAL 60000 #endif /** * @def MY_MAC_ADDRESS * @brief Ethernet MAC address. * * This needs to be unique on the network. */ #ifndef MY_MAC_ADDRESS #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED #endif // Controller ip-address, if this is defined, gateway will act as a client trying to contact controller on MY_PORT. // If MY_CONTROLLER_IP_ADDRESS is left un-defined, gateway acts as server allowing incoming connections. //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254 /************************************** * Node Locking ***************************************/ /** * @defgroup MyLockgrp MyNodeLock * @ingroup internals * @{ * @brief The node lock feature is a security related feature. It locks a node that suspect itself for being * under some form of attack. * * This is achieved by having a counter stored in EEPROM which decrements when suspicious activity is detected. * If the counter reaches 0, node will not work anymore and will transmit a @ref I_LOCKED message to the * gateway/controller with 30m intervals. Payload is a string with a reason for the locking. * The string is abbreviated to accomodate a signature. The following abbreviations exist at the moment: * - LDB (Locked During Boot) * - TMNR (Too Many Nonce Requests) * - TMFV (Too Many Failed Verifications) * * Typically, the counter only decrements when suspicious activity happens in a row. * It is reset if legit traffic is present. * Examples of malicious activity are: * - Repeatedly incorrectly checksummed OTA firmware * - Repeated requests for signing nonces without properly signed messages arriving * - Repeatedly failed signature verifications * * If counter reaches zero, node locks down and EEPROM has to be erased/reset to reactivate node. * Node can also be unlocked by grounding a pin (see @ref MY_NODE_UNLOCK_PIN). * * The size of the counter can be adjusted using @ref MY_NODE_LOCK_COUNTER_MAX. * * @def MY_NODE_LOCK_FEATURE * @brief Enable this to activate intrusion prevention mechanisms on the node. */ //#define MY_NODE_LOCK_FEATURE /** * @def MY_NODE_UNLOCK_PIN * @brief By grounding this pin durig reset of a locked node, the node will unlock. * * If using a secure bootloader, grounding the pin is the only option to reactivate the node. * If using stock Android bootloader or a DualOptiBoot it is also possible to download a sketch * using serial protocol to erase EEPROM to unlock the node. */ #ifndef MY_NODE_UNLOCK_PIN #define MY_NODE_UNLOCK_PIN 14 #endif /** * @def MY_NODE_LOCK_COUNTER_MAX * @brief Maximum accepted occurances of suspected malicious activity in a node. * * Counter decrements on reoccuring incidents but resets if legitimate behaviour is identified. */ #ifndef MY_NODE_LOCK_COUNTER_MAX #define MY_NODE_LOCK_COUNTER_MAX 5 #endif /** @}*/ // Node lock group /********************************** * ESP8266 Defaults ***********************************/ /** * @def MY_ESP8266_SERIAL_MODE * @brief Serial modes: SERIAL_FULL, SERIAL_RX_ONLY, SERIAL_TX_ONLY * * SERIAL_FULL: Default mode. * SERIAL_TX_ONLY: allows to use RX (GPIO3) as a general purpose input/output. * SERIAL_RX_ONLY: allows to use TX (GPIO1) as a general purpose input/output. */ #ifndef MY_ESP8266_SERIAL_MODE #define MY_ESP8266_SERIAL_MODE SERIAL_FULL #endif /************************************** * Linux Settings ***************************************/ /** * @def MY_LINUX_SERIAL_PORT * @brief Serial device port */ #ifndef MY_LINUX_SERIAL_PORT #define MY_LINUX_SERIAL_PORT "/dev/ttyACM0" #endif /** * @def MY_IS_SERIAL_PTY * @brief Set serial as a pseudo terminal. * * Enable this if you need to connect to a controller running on the same device. */ //#define MY_IS_SERIAL_PTY /** * @def MY_LINUX_SERIAL_PTY * @brief Symlink name for the PTY device. */ #ifndef MY_LINUX_SERIAL_PTY #define MY_LINUX_SERIAL_PTY "/dev/ttyMySensorsGateway" #endif /** * @def MY_LINUX_SERIAL_GROUPNAME * @brief Grant access to the specified system group for the serial device. */ //#define MY_LINUX_SERIAL_GROUPNAME "tty" /** * @def MY_LINUX_CONFIG_FILE * @brief Set the filepath for the gateway config file * * For now the configuration file is only used to store the emulated eeprom state */ #ifndef MY_LINUX_CONFIG_FILE #define MY_LINUX_CONFIG_FILE "/etc/mysensors.dat" #endif #endif // MyConfig_h // Doxygen specific constructs, not included when built normally // This is used to enable disabled macros/definitions to be included in the documentation as well. #if DOXYGEN #define MY_SIGNING_ATSHA204 #define MY_SIGNING_SOFT #define MY_SIGNING_REQUEST_SIGNATURES #define MY_SIGNING_GW_REQUEST_SIGNATURES_FROM_ALL #define MY_SIGNING_NODE_WHITELISTING {{.nodeId = GATEWAY_ADDRESS,.serial = {0x09,0x08,0x07,0x06,0x05,0x04,0x03,0x02,0x01}}} #define MY_RS485_HWSERIAL #define MY_IS_RFM69HW #define MY_PARENT_NODE_IS_STATIC #define MY_REGISTRATION_CONTROLLER #define MY_DEBUG_VERBOSE_RF24 #define MY_TRANSPORT_SANITY_CHECK #define MY_RF24_IRQ_PIN #define MY_RX_MESSAGE_BUFFER_FEATURE #define MY_RX_MESSAGE_BUFFER_SIZE #define MY_NODE_LOCK_FEATURE #define MY_REPEATER_FEATURE #define MY_TRANSPORT_DONT_CARE_MODE #define MY_LINUX_SERIAL_GROUPNAME #define MY_IS_SERIAL_PTY #endif