Henrik Ekblad
6165834038
Corrected initialization of radio Add constructor arguments for driver Add defaults to MyConfig Fix ack problems reported on forum.
104 lines
4.0 KiB
C
104 lines
4.0 KiB
C
#ifndef MyConfig_h
|
|
#define MyConfig_h
|
|
#include <stdint.h>
|
|
|
|
// Enable debug flag for debug prints. This will add a lot to the size of the final sketch but good
|
|
// to see what is actually is happening when developing
|
|
#define DEBUG
|
|
|
|
// Serial output baud rate (for debug prints and serial gateway)
|
|
#define BAUD_RATE 115200
|
|
|
|
|
|
/**********************************
|
|
* Over the air firmware updates
|
|
***********************************/
|
|
|
|
// The following define enables the safe over-the-air firmware update feature
|
|
// which requires external flash and the DualOptiBoot bootloader.
|
|
// Note: You can still have OTA FW updates without external flash but it
|
|
// requires the MYSBootloader and disabled MY_OTA_FIRMWARE_FEATURE
|
|
//#define MY_OTA_FIRMWARE_FEATURE
|
|
// Slave select pin for external flash
|
|
#define MY_OTA_FLASH_SS 8
|
|
// Flash jdecid
|
|
#define MY_OTA_FLASH_JDECID 0x1F65
|
|
|
|
|
|
/**********************************
|
|
* Message Signing Settings
|
|
***********************************/
|
|
// Disable to completly disable signing functionality in library
|
|
//#define MY_SIGNING_FEATURE
|
|
|
|
// Define a suitable timeout for a signature verification session
|
|
// Consider the turnaround from a nonce being generated to a signed message being received
|
|
// which might vary, especially in networks with many hops. 5s ought to be enough for anyone.
|
|
#define MY_VERIFICATION_TIMEOUT_MS 5000
|
|
|
|
// Enable to turn on whitelisting
|
|
// When enabled, a signing node will salt the signature with it's unique signature and nodeId.
|
|
// The verifying node will look up the sender in a local table of trusted nodes and
|
|
// do the corresponding salting in order to verify the signature.
|
|
// For this reason, if whitelisting is enabled on one of the nodes in a sign-verify pair, both
|
|
// nodes have to implement whitelisting for this to work.
|
|
// Note that a node can still transmit a non-salted message (i.e. have whitelisting disabled)
|
|
// to a node that has whitelisting enabled (assuming the receiver does not have a matching entry
|
|
// for the sender in it's whitelist)
|
|
//#define MY_SECURE_NODE_WHITELISTING
|
|
|
|
// MySigningAtsha204 default setting
|
|
#define MY_ATSHA204_PIN 17 // A3 - pin where ATSHA204 is attached
|
|
|
|
// MySigningAtsha204Soft default settings
|
|
#define MY_RANDOMSEED_PIN 7 // A7 - Pin used for random generation (do not connect anything to this)
|
|
|
|
// Key to use for HMAC calculation in MySigningAtsha204Soft (32 bytes)
|
|
#define MY_HMAC_KEY 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,\
|
|
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
|
|
|
|
|
|
/**********************************
|
|
* NRF24L01 Driver Defaults
|
|
***********************************/
|
|
#define RF24_CE_PIN 9
|
|
#define RF24_CS_PIN 10
|
|
#define RF24_PA_LEVEL RF24_PA_MAX
|
|
#define RF24_PA_LEVEL_GW RF24_PA_LOW
|
|
// RF channel for the sensor net, 0-127
|
|
#define RF24_CHANNEL 76
|
|
//RF24_250KBPS for 250kbs, RF24_1MBPS for 1Mbps, or RF24_2MBPS for 2Mbps
|
|
#define RF24_DATARATE RF24_250KBPS
|
|
// This is also act as base value for sensor nodeId addresses. Change this (or channel) if you have more than one sensor network.
|
|
#define RF24_BASE_RADIO_ID ((uint64_t)0xA8A8E1FC00LL)
|
|
|
|
// Enable SOFTSPI for NRF24L01 when using the W5100 Ethernet module
|
|
//#define SOFTSPI
|
|
#ifdef SOFTSPI
|
|
// Define the soft SPI pins used for NRF radio
|
|
const uint8_t SOFT_SPI_MISO_PIN = 16;
|
|
const uint8_t SOFT_SPI_MOSI_PIN = 15;
|
|
const uint8_t SOFT_SPI_SCK_PIN = 14;
|
|
#endif
|
|
|
|
|
|
/**********************************
|
|
* RFM69 Driver Defaults
|
|
***********************************/
|
|
// Default network id. Use the same for all nodes that will talk to each other
|
|
#define RFM69_NETWORKID 100
|
|
|
|
// Default frequency to use. This must match the hardware version of the RFM69 radio (uncomment one):
|
|
// #define RFM69_FREQUENCY RF69_433MHZ
|
|
#define RFM69_FREQUENCY RF69_868MHZ
|
|
//#define FREQUENCY RF69_915MHZ
|
|
|
|
// Enable this for encryption of packets
|
|
//#define RFM69_ENABLE_ENCRYPTION
|
|
#define RFM69_ENCRYPTKEY "sampleEncryptKey" //exactly the same 16 characters/bytes on all nodes!
|
|
|
|
|
|
|
|
|
|
#endif
|