Henrik Ekblad
c332667a8d
Serial flush in sleep method also means one less code in examples. Removed set(bool) in message. Not needed. getBool just calls getInt __attribute__((packed)) for RPI compability Print more info in send/read debug prints. Get internalTemp returns full degrees and uses longer Vref delay Fix debug print gateway prepend (wrong command/type) Fixed problem in RelayWithButton example. Now working with ack in both directions. Serial protocol changed (incoming serial message have an new ack-parameter)
119 lines
3.1 KiB
Arduino
119 lines
3.1 KiB
Arduino
// Example sketch showing how to control ir devices
|
|
// An IR LED must be connected to Arduino PWM pin 3.
|
|
// An optional ir receiver can be connected to PWM pin 8.
|
|
// All receied ir signals will be sent to gateway device stored in VAR_1.
|
|
// When binary light on is clicked - sketch will send volume up ir command
|
|
// When binary light off is clicked - sketch will send volume down ir command
|
|
|
|
#include <MySensor.h>
|
|
#include <SPI.h>
|
|
#include <IRLib.h>
|
|
|
|
int RECV_PIN = 8;
|
|
|
|
#define CHILD_1 3 // childId
|
|
|
|
IRsend irsend;
|
|
IRrecv irrecv(RECV_PIN);
|
|
IRdecode decoder;
|
|
//decode_results results;
|
|
unsigned int Buffer[RAWBUF];
|
|
MySensor gw;
|
|
MyMessage msg(CHILD_1, V_VAR1);
|
|
|
|
void setup()
|
|
{
|
|
irrecv.enableIRIn(); // Start the ir receiver
|
|
decoder.UseExtnBuf(Buffer);
|
|
gw.begin(incomingMessage);
|
|
|
|
// Send the sketch version information to the gateway and Controller
|
|
gw.sendSketchInfo("IR Sensor", "1.0");
|
|
|
|
// Register a sensors to gw. Use binary light for test purposes.
|
|
gw.present(CHILD_1, S_LIGHT);
|
|
}
|
|
|
|
|
|
void loop()
|
|
{
|
|
gw.process();
|
|
if (irrecv.GetResults(&decoder)) {
|
|
irrecv.resume();
|
|
decoder.decode();
|
|
decoder.DumpResults();
|
|
|
|
char buffer[10];
|
|
sprintf(buffer, "%08lx", decoder.value);
|
|
// Send ir result to gw
|
|
gw.send(msg.set(buffer));
|
|
}
|
|
}
|
|
|
|
|
|
|
|
void incomingMessage(const MyMessage &message) {
|
|
// We only expect one type of message from controller. But we better check anyway.
|
|
if (message.type==V_LIGHT) {
|
|
int incomingRelayStatus = message.getInt();
|
|
if (incomingRelayStatus == 1) {
|
|
irsend.send(NEC, 0x1EE17887, 32); // Vol up yamaha ysp-900
|
|
} else {
|
|
irsend.send(NEC, 0x1EE1F807, 32); // Vol down yamaha ysp-900
|
|
}
|
|
// Start receiving ir again...
|
|
irrecv.enableIRIn();
|
|
}
|
|
}
|
|
|
|
// Dumps out the decode_results structure.
|
|
// Call this after IRrecv::decode()
|
|
// void * to work around compiler issue
|
|
//void dump(void *v) {
|
|
// decode_results *results = (decode_results *)v
|
|
/*void dump(decode_results *results) {
|
|
int count = results->rawlen;
|
|
if (results->decode_type == UNKNOWN) {
|
|
Serial.print("Unknown encoding: ");
|
|
}
|
|
else if (results->decode_type == NEC) {
|
|
Serial.print("Decoded NEC: ");
|
|
}
|
|
else if (results->decode_type == SONY) {
|
|
Serial.print("Decoded SONY: ");
|
|
}
|
|
else if (results->decode_type == RC5) {
|
|
Serial.print("Decoded RC5: ");
|
|
}
|
|
else if (results->decode_type == RC6) {
|
|
Serial.print("Decoded RC6: ");
|
|
}
|
|
else if (results->decode_type == PANASONIC) {
|
|
Serial.print("Decoded PANASONIC - Address: ");
|
|
Serial.print(results->panasonicAddress,HEX);
|
|
Serial.print(" Value: ");
|
|
}
|
|
else if (results->decode_type == JVC) {
|
|
Serial.print("Decoded JVC: ");
|
|
}
|
|
Serial.print(results->value, HEX);
|
|
Serial.print(" (");
|
|
Serial.print(results->bits, DEC);
|
|
Serial.println(" bits)");
|
|
Serial.print("Raw (");
|
|
Serial.print(count, DEC);
|
|
Serial.print("): ");
|
|
|
|
for (int i = 0; i < count; i++) {
|
|
if ((i % 2) == 1) {
|
|
Serial.print(results->rawbuf[i]*USECPERTICK, DEC);
|
|
}
|
|
else {
|
|
Serial.print(-(int)results->rawbuf[i]*USECPERTICK, DEC);
|
|
}
|
|
Serial.print(" ");
|
|
}
|
|
Serial.println("");
|
|
}
|
|
*/
|