Olivier
8bb3cfb2e1
* Bump version to 2.2.0-beta (#713) * OTA: Add incoming FW block check (#718) * Linux: Add support for SPIDEV (#734) RPi and Linux refactor. Add GPIO Sysfs for GPIO operations. Update configure script. Fix some cppcheck warnings. Add serial emulation that prints to stdout. Fix some file headers. * Fix getControllerConfig() (#737) * Rename MyHwATmega328 to MyHwAVR (#738) * AVR: Restrict fast pin function use (#739) * Fix signing presentation bug (#740) * Consolidate open PRs for bugfix release (#741) * Revert "Bump version to 2.2.0-beta" (#744) * Merge Master into Dev (#745) * Fix spi flash error when compiling in Arduino IDE 1.6.6 * Bump minor version * Fixed "invalid suffix on literal" warning * Fix addressing bug in _doSign bitfield * Make sure nodes not supporting signing informs GW A node that does not support signing, still needs to inform the gateway about this to make sure the gateway carries a valid signing requirement table when a node Id that was requiering signing stops doing this. This fixes #286. * Prevent SecureActuator from accepting ACKs as commands As ACKs are not currently signed, allowing ACKs as commands is a considerable security hole for this sketch. This is now resolved. * Backport of bugfix (#259) in repeaters when forwarding signed messages * Bumped version to 1.5.2 * Corrected doSign variable name (was _doSign) * Bumped version to 1.5.3 * Add NULL termination to payloads Messages addressed to "this" node, will have a null char appended to the payload after message verification is done, because some "getters" assume the message being a string. * MySensors 2.1.1 release
106 lines
2.8 KiB
Arduino
106 lines
2.8 KiB
Arduino
/***
|
|
* This is a simple sketch used to demenstrate and test node-to-node MySensor's communication.
|
|
* To use this sketch, assemble MySensors nodes - they need nothing more than a radio
|
|
* 1. Flash each node with the same sketch, open the console and type either 0 or 1 to the respective nodes to set thei ID
|
|
* 2. You only need to set the node id once, and restart the nodes
|
|
* 3. To being a ping-pong test, simply type T in the console for one of the nodes.
|
|
*
|
|
* 2015-05-25 Bruce Lacey v1.0
|
|
*/
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
// Enable and select radio type attached
|
|
#define MY_RADIO_NRF24
|
|
//#define MY_RADIO_RFM69
|
|
|
|
#include <MySensors.h>
|
|
#include "MYSLog.h"
|
|
|
|
#define VSN "v1.0"
|
|
|
|
// Define two generic nodes with a single child
|
|
#define YING 200
|
|
#define YANG 201
|
|
#define CHILD 1
|
|
|
|
MyMessage mPing(CHILD, V_VAR1); //Ping message
|
|
MyMessage mPong(CHILD, V_VAR2); //Pong message
|
|
|
|
void setup()
|
|
{
|
|
}
|
|
|
|
void presentation()
|
|
{
|
|
present(CHILD, S_CUSTOM); //
|
|
|
|
sendSketchInfo( nodeTypeAsCharRepresentation( getNodeId() ), VSN );
|
|
LOG(F("\n%sReady.\n"), nodeTypeAsCharRepresentation(getNodeId()));
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
|
|
// Interactive command and control
|
|
// Entering a number from 0 or 1 will write the node 200 (YING) or 201 (YANG) to EEPROM
|
|
// Entering T on either node will initiatve a ping-pong test.
|
|
if (Serial.available()) {
|
|
byte inChar = Serial.read();
|
|
uint8_t node = getNodeId();
|
|
|
|
// Manual Test Mode
|
|
if (inChar == 'T' || inChar == 't') {
|
|
LOG(F("T received - starting test...\n"));
|
|
MyMessage msg = mPong;
|
|
msg.sender = (node == YING ? YANG : YING);
|
|
sendPingOrPongResponse( msg );
|
|
} else if (inChar == '0' or inChar == '1') {
|
|
byte nodeID = 200 + (inChar - '0');
|
|
setNodeId(nodeID);
|
|
} else {
|
|
LOG("Invalid input\n");
|
|
}
|
|
}
|
|
}
|
|
|
|
void receive(const MyMessage &message)
|
|
{
|
|
|
|
LOG(F("Received %s from %s\n"), msgTypeAsCharRepresentation((mysensor_data)message.type),
|
|
nodeTypeAsCharRepresentation(message.sender));
|
|
|
|
delay(250);
|
|
sendPingOrPongResponse( message );
|
|
}
|
|
|
|
void sendPingOrPongResponse( MyMessage msg )
|
|
{
|
|
|
|
MyMessage response = (msg.type == V_VAR1 ? mPong : mPing);
|
|
|
|
LOG(F("Sending %s to %s\n"), msgTypeAsCharRepresentation( (mysensor_data)response.type ),
|
|
nodeTypeAsCharRepresentation(msg.sender));
|
|
|
|
// Set payload to current time in millis to ensure each message is unique
|
|
response.set( (uint32_t)millis() );
|
|
response.setDestination(msg.sender);
|
|
send(response);
|
|
}
|
|
|
|
void setNodeId(byte nodeID)
|
|
{
|
|
LOG(F("Setting node id to: %i.\n***Please restart the node for changes to take effect.\n"), nodeID);
|
|
hwWriteConfig(EEPROM_NODE_ID_ADDRESS, (byte)nodeID);
|
|
}
|
|
|
|
const char * msgTypeAsCharRepresentation( mysensor_data mType )
|
|
{
|
|
return mType == V_VAR1 ? "Ping" : "Pong";
|
|
}
|
|
|
|
const char * nodeTypeAsCharRepresentation( uint8_t node )
|
|
{
|
|
return node == YING ? "Ying Node" : "Yang Node";
|
|
} |