146 lines
4.7 KiB
Arduino
146 lines
4.7 KiB
Arduino
/**
|
|
* The MySensors Arduino library handles the wireless radio link and protocol
|
|
* between your home built sensors/actuators and HA controller of choice.
|
|
* The sensors forms a self healing radio network with optional repeaters. Each
|
|
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
|
|
* network topology allowing messages to be routed to nodes.
|
|
*
|
|
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
|
|
* Copyright (C) 2013-2015 Sensnology AB
|
|
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
|
|
*
|
|
* Documentation: http://www.mysensors.org
|
|
* Support Forum: http://forum.mysensors.org
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
*******************************
|
|
*
|
|
* REVISION HISTORY
|
|
* Version 1.0 - Henrik Ekblad
|
|
*
|
|
* DESCRIPTION
|
|
* The ESP8266 MQTT gateway sends radio network (or locally attached sensors) data to your MQTT broker.
|
|
* The node also listens to MY_MQTT_TOPIC_PREFIX and sends out those messages to the radio network
|
|
*
|
|
* LED purposes:
|
|
* - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
|
|
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
|
|
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
|
|
* - ERR (red) - fast blink on error during transmission error or recieve crc error
|
|
*
|
|
* See http://www.mysensors.org/build/esp8266_gateway for wiring instructions.
|
|
* nRF24L01+ ESP8266
|
|
* VCC VCC
|
|
* CE GPIO4
|
|
* CSN/CS GPIO15
|
|
* SCK GPIO14
|
|
* MISO GPIO12
|
|
* MOSI GPIO13
|
|
*
|
|
* Not all ESP8266 modules have all pins available on their external interface.
|
|
* This code has been tested on an ESP-12 module.
|
|
* The ESP8266 requires a certain pin configuration to download code, and another one to run code:
|
|
* - Connect REST (reset) via 10K pullup resistor to VCC, and via switch to GND ('reset switch')
|
|
* - Connect GPIO15 via 10K pulldown resistor to GND
|
|
* - Connect CH_PD via 10K resistor to VCC
|
|
* - Connect GPIO2 via 10K resistor to VCC
|
|
* - Connect GPIO0 via 10K resistor to VCC, and via switch to GND ('bootload switch')
|
|
*
|
|
* Inclusion mode button:
|
|
* - Connect GPIO5 via switch to GND ('inclusion switch')
|
|
*
|
|
* Hardware SHA204 signing is currently not supported!
|
|
*
|
|
* Make sure to fill in your ssid and WiFi password below for ssid & pass.
|
|
*/
|
|
|
|
#include <EEPROM.h>
|
|
#include <SPI.h>
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
// Use a bit lower baudrate for serial prints on ESP8266 than default in MyConfig.h
|
|
#define MY_BAUD_RATE 9600
|
|
|
|
// Enables and select radio type (if attached)
|
|
#define MY_RADIO_NRF24
|
|
//#define MY_RADIO_RFM69
|
|
|
|
#define MY_GATEWAY_MQTT_CLIENT
|
|
#define MY_GATEWAY_ESP8266
|
|
|
|
// Set this node's subscribe and publish topic prefix
|
|
#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out"
|
|
#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in"
|
|
|
|
// Set MQTT client id
|
|
#define MY_MQTT_CLIENT_ID "mysensors-1"
|
|
|
|
// Enable these if your MQTT broker requires usenrame/password
|
|
//#define MY_MQTT_USER "username"
|
|
//#define MY_MQTT_PASSWORD "password"
|
|
|
|
// Set WIFI SSID and password
|
|
#define MY_ESP8266_SSID "MySSID"
|
|
#define MY_ESP8266_PASSWORD "MyVerySecretPassword"
|
|
|
|
// Set the hostname for the WiFi Client. This is the hostname
|
|
// it will pass to the DHCP server if not static.
|
|
// #define MY_ESP8266_HOSTNAME "mqtt-sensor-gateway"
|
|
|
|
// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
|
|
#define MY_IP_ADDRESS 192,168,178,87
|
|
|
|
// If using static ip you need to define Gateway and Subnet address as well
|
|
#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
|
|
#define MY_IP_SUBNET_ADDRESS 255,255,255,0
|
|
|
|
|
|
// MQTT broker ip address.
|
|
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
|
|
|
|
// The MQTT broker port to to open
|
|
#define MY_PORT 1883
|
|
|
|
/*
|
|
// Flash leds on rx/tx/err
|
|
#define MY_LEDS_BLINKING_FEATURE
|
|
// Set blinking period
|
|
#define MY_DEFAULT_LED_BLINK_PERIOD 300
|
|
|
|
// Enable inclusion mode
|
|
#define MY_INCLUSION_MODE_FEATURE
|
|
// Enable Inclusion mode button on gateway
|
|
#define MY_INCLUSION_BUTTON_FEATURE
|
|
// Set inclusion mode duration (in seconds)
|
|
#define MY_INCLUSION_MODE_DURATION 60
|
|
// Digital pin used for inclusion mode button
|
|
#define MY_INCLUSION_MODE_BUTTON_PIN 3
|
|
|
|
#define MY_DEFAULT_ERR_LED_PIN 16 // Error led pin
|
|
#define MY_DEFAULT_RX_LED_PIN 16 // Receive led pin
|
|
#define MY_DEFAULT_TX_LED_PIN 16 // the PCB, on board LED
|
|
*/
|
|
|
|
#include <ESP8266WiFi.h>
|
|
#include <MySensors.h>
|
|
|
|
void setup() {
|
|
}
|
|
|
|
void presentation() {
|
|
// Present locally attached sensors here
|
|
}
|
|
|
|
|
|
void loop() {
|
|
// Send locally attech sensors data here
|
|
}
|
|
|
|
|
|
|