104 lines
3.3 KiB
Arduino
104 lines
3.3 KiB
Arduino
/**
|
|
* The MySensors Arduino library handles the wireless radio link and protocol
|
|
* between your home built sensors/actuators and HA controller of choice.
|
|
* The sensors forms a self healing radio network with optional repeaters. Each
|
|
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
|
|
* network topology allowing messages to be routed to nodes.
|
|
*
|
|
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
|
|
* Copyright (C) 2013-2015 Sensnology AB
|
|
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
|
|
*
|
|
* Documentation: http://www.mysensors.org
|
|
* Support Forum: http://forum.mysensors.org
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
*******************************
|
|
*
|
|
* DESCRIPTION
|
|
* The RS485 Gateway prints data received from sensors on the serial link.
|
|
* The gateway accepts input on seral which will be sent out on
|
|
* the RS485 link.
|
|
*
|
|
* Wire connections (OPTIONAL):
|
|
* - Inclusion button should be connected between digital pin 3 and GND
|
|
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
|
|
*
|
|
* LEDs (OPTIONAL):
|
|
* - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h
|
|
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
|
|
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
|
|
* - ERR (red) - fast blink on error during transmission error or recieve crc error
|
|
*
|
|
* The gateway uses AltSoftSerial to handle two serial links
|
|
* on one Arduino. Use the following pins for RS485 link
|
|
*
|
|
* Board Transmit Receive PWM Unusable
|
|
* ----- -------- ------- ------------
|
|
* Teensy 3.0 & 3.1 21 20 22
|
|
* Teensy 2.0 9 10 (none)
|
|
* Teensy++ 2.0 25 4 26, 27
|
|
* Arduino Uno 9 8 10
|
|
* Arduino Leonardo 5 13 (none)
|
|
* Arduino Mega 46 48 44, 45
|
|
* Wiring-S 5 6 4
|
|
* Sanguino 13 14 12
|
|
*
|
|
*/
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
// Enable RS485 transport layer
|
|
#define MY_RS485
|
|
|
|
// Define this to enables DE-pin management on defined pin
|
|
#define MY_RS485_DE_PIN 2
|
|
|
|
// Set RS485 baud rate to use
|
|
#define MY_RS485_BAUD_RATE 9600
|
|
|
|
// Enable serial gateway
|
|
#define MY_GATEWAY_SERIAL
|
|
|
|
// Flash leds on rx/tx/err
|
|
#define MY_LEDS_BLINKING_FEATURE
|
|
// Set blinking period
|
|
#define MY_DEFAULT_LED_BLINK_PERIOD 300
|
|
|
|
// Enable inclusion mode
|
|
#define MY_INCLUSION_MODE_FEATURE
|
|
// Enable Inclusion mode button on gateway
|
|
#define MY_INCLUSION_BUTTON_FEATURE
|
|
// Set inclusion mode duration (in seconds)
|
|
#define MY_INCLUSION_MODE_DURATION 60
|
|
// Digital pin used for inclusion mode button
|
|
#define MY_INCLUSION_MODE_BUTTON_PIN 3
|
|
|
|
#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
|
|
#define MY_DEFAULT_RX_LED_PIN 5 // Receive led pin
|
|
#define MY_DEFAULT_TX_LED_PIN 6 // the PCB, on board LED
|
|
|
|
#include <SPI.h>
|
|
#include <MySensors.h>
|
|
|
|
void setup() {
|
|
// Setup locally attached sensors
|
|
}
|
|
|
|
void presentation() {
|
|
// Present locally attached sensors
|
|
}
|
|
|
|
void loop() {
|
|
// Send locally attached sensor data here
|
|
}
|
|
|
|
|
|
|
|
|
|
|