EthernetGateway: Use internal LEDs feature for blinking

Signed-off-by: Tomas Hozza <thozza@gmail.com>

libraries/MySensors/examples/EthernetGateway/EthernetGateway.ino

@@ -46,6 +46,7 @@
  * E.g. If you want to use the defualt values in this sketch enter: 192.168.178.66:5003
  *
  * LED purposes:
+ * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
  * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
  * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
  * - ERR (red) - fast blink on error during transmission error or recieve crc error  
@@ -68,7 +69,6 @@
 #include <MyParserSerial.h>  
 #include <MySensor.h>  
 #include <stdarg.h>
-#include <MsTimer2.h>
 #include <PinChangeInt.h>
 #include "GatewayUtil.h"
 
@@ -104,7 +104,12 @@ MyTransportNRF24 transport(RF24_CE_PIN, RF24_CS_PIN, RF24_PA_LEVEL_GW);
 MyHwATMega328 hw;
 
 // Construct MySensors library (signer needed if MY_SIGNING_FEATURE is turned on in MyConfig.h)
+// To use LEDs blinking, uncomment WITH_LEDS_BLINKING in MyConfig.h
+#ifdef WITH_LEDS_BLINKING
+MySensor gw(transport, hw /*, signer*/, RADIO_RX_LED_PIN, RADIO_TX_LED_PIN, RADIO_ERROR_LED_PIN);
+#else
 MySensor gw(transport, hw /*, signer*/);
+#endif
 
 
 #define IP_PORT 5003        // The port you want to open 
@@ -136,11 +141,8 @@ void output(const char *fmt, ... ) {
 void setup()  
 { 
   Ethernet.begin(mac, myIp);
-  setupGateway(RADIO_RX_LED_PIN, RADIO_TX_LED_PIN, RADIO_ERROR_LED_PIN, INCLUSION_MODE_PIN, INCLUSION_MODE_TIME, output);
 
-  // Add led timer interrupt
+  setupGateway(INCLUSION_MODE_PIN, INCLUSION_MODE_TIME, output);
-  MsTimer2::set(300, ledTimersInterrupt);
-  MsTimer2::start();
 
   // Add interrupt for inclusion button to pin
   PCintPort::attachInterrupt(pinInclusion, startInclusionInterrupt, RISING);

libraries/MySensors/examples/EthernetGateway/GatewayUtil.h

@@ -7,9 +7,6 @@
 #ifdef ARDUINO
 
 
-uint8_t pinRx = 8; // Rx led pin
-uint8_t pinTx = 9; // Tx led pin
-uint8_t pinEr = 7; // Err led pin
 uint8_t inclusionTime = 1; // Number of minutes inclusion mode is enabled
 uint8_t pinInclusion =  3; // Input pin that should trigger inclusion mode
 
@@ -17,56 +14,28 @@ uint8_t pinInclusion =  3; // Input pin that should trigger inclusion mode
 #define MAX_SEND_LENGTH 120 // Max buffersize needed for messages destined for controller
 
 volatile boolean buttonTriggeredInclusion;
-volatile uint8_t countRx;
-volatile uint8_t countTx;
-volatile uint8_t countErr;
 boolean inclusionMode; // Keeps track on inclusion mode
 void (*serial)(const char *fmt, ... );
 
 MyParserSerial parser;
 
 void setInclusionMode(boolean newMode);
-void txBlink(uint8_t cnt);
-void rxBlink(uint8_t cnt);
-void errBlink(uint8_t cnt);
 
 char convBuf[MAX_PAYLOAD*2+1];
 char serialBuffer[MAX_SEND_LENGTH]; // Buffer for building string when sending data to vera
 unsigned long inclusionStartTime;
 
-void setupGateway(uint8_t _rx, uint8_t _tx, uint8_t _er, uint8_t _inc, uint8_t _incTime, void (* _serial)(const char *, ... )) {
+void setupGateway(uint8_t _inc, uint8_t _incTime, void (* _serial)(const char *, ... )) {
   inclusionMode = 0;
   buttonTriggeredInclusion = false;
   serial = _serial;
 
-  pinRx = _rx;
-  pinTx = _tx;
-  pinEr = _er;
   pinInclusion = _inc;
   inclusionTime = _incTime;
   
-  countRx = 0;
-  countTx = 0;
-  countErr = 0;
-
-
-  // Setup led pins
-  pinMode(pinRx, OUTPUT);
-  pinMode(pinTx, OUTPUT);
-  pinMode(pinEr, OUTPUT);
-  digitalWrite(pinRx, LOW);
-  digitalWrite(pinTx, LOW);
-  digitalWrite(pinEr, LOW);
-
   // Setup digital in that triggers inclusion mode
   pinMode(pinInclusion, INPUT);
   digitalWrite(pinInclusion, HIGH);
-
-  // Set initial state of leds
-  digitalWrite(pinRx, HIGH);
-  digitalWrite(pinTx, HIGH);
-  digitalWrite(pinEr, HIGH);
-
 }
 
 
@@ -76,11 +45,11 @@ void startInclusionInterrupt() {
 }
 
 void incomingMessage(const MyMessage &message) {
-  if (mGetCommand(message) == C_PRESENTATION && inclusionMode) {
+//  if (mGetCommand(message) == C_PRESENTATION && inclusionMode) {
-	rxBlink(3);
+//	gw.rxBlink(3);
-   } else {
+//   } else {
-	rxBlink(1);
+//	gw.rxBlink(1);
-   }
+//   }
    // Pass along the message from sensors to serial line
    serial(PSTR("%d;%d;%d;%d;%d;%s\n"),message.sender, message.sensor, mGetCommand(message), mGetAck(message), message.type, message.getString(convBuf));
 } 
@@ -106,7 +75,7 @@ void checkInclusionFinished() {
   }
 }
 
-void parseAndSend(MySensor gw, char *commandBuffer) {
+void parseAndSend(MySensor &gw, char *commandBuffer) {
   boolean ok;
   MyMessage &msg = gw.getLastMessage();
 
@@ -123,10 +92,14 @@ void parseAndSend(MySensor gw, char *commandBuffer) {
         setInclusionMode(atoi(msg.data) == 1);
       }
     } else {
-      txBlink(1);
+      #ifdef WITH_LEDS_BLINKING
+      gw.txBlink(1);
+      #endif
       ok = gw.sendRoute(msg);
       if (!ok) {
-        errBlink(1);
+        #ifdef WITH_LEDS_BLINKING
+        gw.errBlink(1);
+        #endif
       }
     }
   }
@@ -145,50 +118,6 @@ void setInclusionMode(boolean newMode) {
 }
 
 
-
-
-void ledTimersInterrupt() {
-  if(countRx && countRx != 255) {
-    // switch led on
-    digitalWrite(pinRx, LOW);
-  } else if(!countRx) {
-     // switching off
-     digitalWrite(pinRx, HIGH);
-   }
-   if(countRx != 255) { countRx--; }
-
-  if(countTx && countTx != 255) {
-    // switch led on
-    digitalWrite(pinTx, LOW);
-  } else if(!countTx) {
-     // switching off
-     digitalWrite(pinTx, HIGH);
-   }
-   if(countTx != 255) { countTx--; }
-   else if(inclusionMode) { countTx = 8; }
-
-  if(countErr && countErr != 255) {
-    // switch led on
-    digitalWrite(pinEr, LOW);
-  } else if(!countErr) {
-     // switching off
-     digitalWrite(pinEr, HIGH);
-   }
-   if(countErr != 255) { countErr--; }
-}
-
-void rxBlink(uint8_t cnt) {
-  if(countRx == 255) { countRx = cnt; }
-}
-void txBlink(uint8_t cnt) {
-  if(countTx == 255 && !inclusionMode) { countTx = cnt; }
-}
-void errBlink(uint8_t cnt) {
-  if(countErr == 255) { countErr = cnt; }
-}
-
-
-
 #else
 #error This example is only for use on Arduino.
 #endif // ARDUINO