Merge development branch

MyConfig.h

@@ -459,6 +459,8 @@
 		#define MY_RF24_CE_PIN 4
 	#elif defined(ARDUINO_ARCH_SAMD)
 		#define MY_RF24_CE_PIN 27
+	#elif defined(LINUX_ARCH_RASPBERRYPI)
+		#define MY_RF24_CE_PIN 22
 	#else
 		#define MY_RF24_CE_PIN 9
 	#endif
@@ -473,6 +475,8 @@
 		#define MY_RF24_CS_PIN 15
 	#elif defined(ARDUINO_ARCH_SAMD)
 		#define MY_RF24_CS_PIN 3
+	#elif defined(LINUX_ARCH_RASPBERRYPI)
+		#define MY_RF24_CS_PIN 24
 	#else
 		#define MY_RF24_CS_PIN 10
 	#endif
@@ -654,6 +658,7 @@
 //#define MY_GATEWAY_W5100
 //#define MY_GATEWAY_ENC28J60
 //#define MY_GATEWAY_ESP8266
+//#define MY_GATEWAY_LINUX
 
 /**
  * @def MY_PORT
@@ -695,6 +700,10 @@
 // If MY_CONTROLLER_IP_ADDRESS is left un-defined, gateway acts as server allowing incoming connections.
 //#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254
 
+/**************************************
+* Node Locking
+***************************************/
+
 /**
  * @defgroup MyLockgrp MyNodeLock
  * @ingroup internals
@@ -751,8 +760,68 @@
 #endif
 /** @}*/ // Node lock group
 
+/**********************************
+*  ESP8266 Defaults
+***********************************/
+
+/**
+ * @def MY_ESP8266_SERIAL_MODE
+ * @brief Serial modes: SERIAL_FULL, SERIAL_RX_ONLY, SERIAL_TX_ONLY
+ *
+ * SERIAL_FULL: Default mode.
+ * SERIAL_TX_ONLY: allows to use RX (GPIO3) as a general purpose input/output.
+ * SERIAL_RX_ONLY: allows to use TX (GPIO1) as a general purpose input/output.
+ */
+#ifndef MY_ESP8266_SERIAL_MODE
+#define MY_ESP8266_SERIAL_MODE SERIAL_FULL
 #endif
 
+/**************************************
+* Linux Settings
+***************************************/
+
+/**
+ * @def MY_LINUX_SERIAL_PORT
+ * @brief Serial device port
+ */
+#ifndef MY_LINUX_SERIAL_PORT
+#define MY_LINUX_SERIAL_PORT "/dev/ttyACM0"
+#endif
+
+/**
+ * @def MY_IS_SERIAL_PTY
+ * @brief Set serial as a pseudo terminal.
+ *
+ * Enable this if you need to connect to a controller running on the same device.
+ */
+//#define MY_IS_SERIAL_PTY
+
+/**
+ * @def MY_LINUX_SERIAL_PTY
+ * @brief Symlink name for the PTY device.
+ */
+#ifndef MY_LINUX_SERIAL_PTY
+#define MY_LINUX_SERIAL_PTY "/dev/ttyMySensorsGateway"
+#endif
+
+/**
+ * @def MY_LINUX_SERIAL_GROUPNAME
+ * @brief Grant access to the specified system group for the serial device.
+ */
+//#define MY_LINUX_SERIAL_GROUPNAME "tty"
+
+/**
+ * @def MY_LINUX_CONFIG_FILE
+ * @brief Set the filepath for the gateway config file
+ *
+ * For now the configuration file is only used to store the emulated eeprom state
+ */
+#ifndef MY_LINUX_CONFIG_FILE
+#define MY_LINUX_CONFIG_FILE "/etc/mysensors.dat"
+#endif
+
+#endif	// MyConfig_h
+
 // Doxygen specific constructs, not included when built normally
 // This is used to enable disabled macros/definitions to be included in the documentation as well.
 #if DOXYGEN
@@ -771,4 +840,6 @@
 #define MY_NODE_LOCK_FEATURE
 #define MY_REPEATER_FEATURE
 #define MY_TRANSPORT_DONT_CARE_MODE
+#define MY_LINUX_SERIAL_GROUPNAME
+#define MY_IS_SERIAL_PTY
 #endif