Vibration sensor sketch

2015-08-10 21:56:33 +02:00
parent 059d034f10
commit e40939fba7
1 changed files with 94 additions and 0 deletions
@@ -0,0 +1,94 @@
+/**
+ * The MySensors Arduino library handles the wireless radio link and protocol
+ * between your home built sensors/actuators and HA controller of choice.
+ * The sensors forms a self healing radio network with optional repeaters. Each
+ * repeater and gateway builds a routing tables in EEPROM which keeps track of the
+ * network topology allowing messages to be routed to nodes.
+ *
+ * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
+ * Copyright (C) 2013-2015 Sensnology AB
+ * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
+ *
+ * Documentation: http://www.mysensors.org
+ * Support Forum: http://forum.mysensors.org
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ *******************************
+ *
+ * DESCRIPTION
+ *
+ * Vibration Sensor
+ *
+ * connect the sensor as follows :
+ *
+ * VCC       >>> 5V
+ * S         >>> D3
+ * GND       >>> GND
+ *
+ * Based on: http://www.dfrobot.com/wiki/index.php/DFRobot_Digital_Vibration_Sensor_V2_SKU:DFR0027
+ * Contributor: epierre
+**/
+
+
+#include <MySensor.h>
+#include <SPI.h>
+#include <Wire.h>
+
+#define CHILD_ID_VIBRATION 0
+#define VIBRATION_SENSOR_DIGITAL_PIN 3
+#define SensorLED     13
+
+unsigned long SLEEP_TIME = 10*1000; // Sleep time between reads (in seconds)
+
+//VARIABLES
+int val = 0;           // variable to store the value coming from the sensor
+float valVIBRATION =0.0;
+float lastVIBRATION =0.0;
+unsigned char state = 0;
+
+MySensor gw;
+MyMessage vibrationMsg(CHILD_ID_VIBRATION, V_LEVEL);
+
+void setup()  
+{
+  gw.begin();
+
+  // Send the sketch version information to the gateway and Controller
+  gw.sendSketchInfo("VIBRATION Sensor", "1.0");
+
+  // Register all sensors to gateway (they will be created as child devices)
+  gw.present(CHILD_ID_VIBRATION, S_VIBRATION);
+
+  
+  pinMode(VIBRATION_SENSOR_DIGITAL_PIN, INPUT);
+  attachInterrupt(1, blink, FALLING);// Trigger the blink function when the falling edge is detected
+  pinMode(SensorLED, OUTPUT);  
+}
+
+void loop()      
+{    
+  
+  if(state>=40){ // basically below 40 so ignire basic level
+        gw.send(vibrationMsg.set(int(state)));
+        state = 0;  
+        digitalWrite(SensorLED,HIGH);
+   }    else {
+        state = 0;  
+        digitalWrite(SensorLED,LOW);
+  } 
+
+  
+  // Power down the radio.  Note that the radio will get powered back up
+  // on the next write() call.
+  delay(1000); //delay to allow serial to fully print before sleep
+
+  gw.sleep(SLEEP_TIME); //sleep for: sleepTime
+}
+
+void blink()//Interrupts function
+{
+  state++;
+}