Merge pull request #477 from tekka007/StaticENUMS
Define static enums in MyMessage
This commit is contained in:
Patrick Fallberg
GitHub
@@ -43,186 +43,177 @@
|
||||
|
||||
/// @brief The command field (message-type) defines the overall properties of a message
|
||||
typedef enum {
|
||||
C_PRESENTATION = 0, //!< Sent by a node when they present attached sensors. This is usually done in presentation() at startup.
|
||||
C_SET = 1, //!< This message is sent from or to a sensor when a sensor value should be updated.
|
||||
C_REQ = 2, //!< Requests a variable value (usually from an actuator destined for controller).
|
||||
C_INTERNAL = 3, //!< Internal MySensors messages (also include common messages provided/generated by the library).
|
||||
C_STREAM = 4 //!< For firmware and other larger chunks of data that need to be divided into pieces.
|
||||
C_PRESENTATION = 0, //!< Sent by a node when they present attached sensors. This is usually done in presentation() at startup.
|
||||
C_SET = 1, //!< This message is sent from or to a sensor when a sensor value should be updated.
|
||||
C_REQ = 2, //!< Requests a variable value (usually from an actuator destined for controller).
|
||||
C_INTERNAL = 3, //!< Internal MySensors messages (also include common messages provided/generated by the library).
|
||||
C_STREAM = 4 //!< For firmware and other larger chunks of data that need to be divided into pieces.
|
||||
} mysensor_command;
|
||||
|
||||
/// @brief Type of sensor (used when presenting sensors)
|
||||
typedef enum {
|
||||
S_DOOR, // Door sensor, V_TRIPPED, V_ARMED
|
||||
S_MOTION, // Motion sensor, V_TRIPPED, V_ARMED
|
||||
S_SMOKE, // Smoke sensor, V_TRIPPED, V_ARMED
|
||||
S_LIGHT, // Binary light or relay, V_STATUS (or V_LIGHT), V_WATT
|
||||
S_BINARY=3, // Binary light or relay, V_STATUS (or V_LIGHT), V_WATT (same as S_LIGHT)
|
||||
S_DIMMER, // Dimmable light or fan device, V_STATUS (on/off), V_DIMMER (dimmer level 0-100), V_WATT
|
||||
S_COVER, // Blinds or window cover, V_UP, V_DOWN, V_STOP, V_DIMMER (open/close to a percentage)
|
||||
S_TEMP, // Temperature sensor, V_TEMP
|
||||
S_HUM, // Humidity sensor, V_HUM
|
||||
S_BARO, // Barometer sensor, V_PRESSURE, V_FORECAST
|
||||
S_WIND, // Wind sensor, V_WIND, V_GUST
|
||||
S_RAIN, // Rain sensor, V_RAIN, V_RAINRATE
|
||||
S_UV, // Uv sensor, V_UV
|
||||
S_WEIGHT, // Personal scale sensor, V_WEIGHT, V_IMPEDANCE
|
||||
S_POWER, // Power meter, V_WATT, V_KWH, V_VAR, V_VA, V_POWER_FACTOR
|
||||
S_HEATER, // Header device, V_HVAC_SETPOINT_HEAT, V_HVAC_FLOW_STATE, V_TEMP
|
||||
S_DISTANCE, // Distance sensor, V_DISTANCE
|
||||
S_LIGHT_LEVEL, // Light level sensor, V_LIGHT_LEVEL (uncalibrated in percentage), V_LEVEL (light level in lux)
|
||||
S_ARDUINO_NODE, // Used (internally) for presenting a non-repeating Arduino node
|
||||
S_ARDUINO_REPEATER_NODE, // Used (internally) for presenting a repeating Arduino node
|
||||
S_LOCK, // Lock device, V_LOCK_STATUS
|
||||
S_IR, // Ir device, V_IR_SEND, V_IR_RECEIVE
|
||||
S_WATER, // Water meter, V_FLOW, V_VOLUME
|
||||
S_AIR_QUALITY, // Air quality sensor, V_LEVEL
|
||||
S_CUSTOM, // Custom sensor
|
||||
S_DUST, // Dust sensor, V_LEVEL
|
||||
S_SCENE_CONTROLLER, // Scene controller device, V_SCENE_ON, V_SCENE_OFF.
|
||||
S_RGB_LIGHT, // RGB light. Send color component data using V_RGB. Also supports V_WATT
|
||||
S_RGBW_LIGHT, // RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT
|
||||
S_COLOR_SENSOR, // Color sensor, send color information using V_RGB
|
||||
S_HVAC, // Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT, V_HVAC_SETPOINT_COLD, V_HVAC_FLOW_STATE, V_HVAC_FLOW_MODE, V_TEMP
|
||||
S_MULTIMETER, // Multimeter device, V_VOLTAGE, V_CURRENT, V_IMPEDANCE
|
||||
S_SPRINKLER, // Sprinkler, V_STATUS (turn on/off), V_TRIPPED (if fire detecting device)
|
||||
S_WATER_LEAK, // Water leak sensor, V_TRIPPED, V_ARMED
|
||||
S_SOUND, // Sound sensor, V_TRIPPED, V_ARMED, V_LEVEL (sound level in dB)
|
||||
S_VIBRATION, // Vibration sensor, V_TRIPPED, V_ARMED, V_LEVEL (vibration in Hz)
|
||||
S_MOISTURE, // Moisture sensor, V_TRIPPED, V_ARMED, V_LEVEL (water content or moisture in percentage?)
|
||||
S_INFO, // LCD text device / Simple information device on controller, V_TEXT
|
||||
S_GAS, // Gas meter, V_FLOW, V_VOLUME
|
||||
S_GPS, // GPS Sensor, V_POSITION
|
||||
S_WATER_QUALITY,// V_TEMP, V_PH, V_ORP, V_EC, V_STATUS
|
||||
S_DOOR = 0, //!< Door sensor, V_TRIPPED, V_ARMED
|
||||
S_MOTION = 1, //!< Motion sensor, V_TRIPPED, V_ARMED
|
||||
S_SMOKE = 2, //!< Smoke sensor, V_TRIPPED, V_ARMED
|
||||
S_BINARY = 3, //!< Binary light or relay, V_STATUS, V_WATT
|
||||
S_LIGHT = 3, //!< \deprecated Same as S_BINARY, **** DEPRECATED, DO NOT USE ****
|
||||
S_DIMMER = 4, //!< Dimmable light or fan device, V_STATUS (on/off), V_PERCENTAGE (dimmer level 0-100), V_WATT
|
||||
S_COVER = 5, //!< Blinds or window cover, V_UP, V_DOWN, V_STOP, V_PERCENTAGE (open/close to a percentage)
|
||||
S_TEMP = 6, //!< Temperature sensor, V_TEMP
|
||||
S_HUM = 7, //!< Humidity sensor, V_HUM
|
||||
S_BARO = 8, //!< Barometer sensor, V_PRESSURE, V_FORECAST
|
||||
S_WIND = 9, //!< Wind sensor, V_WIND, V_GUST
|
||||
S_RAIN = 10, //!< Rain sensor, V_RAIN, V_RAINRATE
|
||||
S_UV = 11, //!< Uv sensor, V_UV
|
||||
S_WEIGHT = 12, //!< Personal scale sensor, V_WEIGHT, V_IMPEDANCE
|
||||
S_POWER = 13, //!< Power meter, V_WATT, V_KWH, V_VAR, V_VA, V_POWER_FACTOR
|
||||
S_HEATER = 14, //!< Header device, V_HVAC_SETPOINT_HEAT, V_HVAC_FLOW_STATE, V_TEMP
|
||||
S_DISTANCE = 15, //!< Distance sensor, V_DISTANCE
|
||||
S_LIGHT_LEVEL = 16, //!< Light level sensor, V_LIGHT_LEVEL (uncalibrated in percentage), V_LEVEL (light level in lux)
|
||||
S_ARDUINO_NODE = 17, //!< Used (internally) for presenting a non-repeating Arduino node
|
||||
S_ARDUINO_REPEATER_NODE = 18, //!< Used (internally) for presenting a repeating Arduino node
|
||||
S_LOCK = 19, //!< Lock device, V_LOCK_STATUS
|
||||
S_IR = 20, //!< IR device, V_IR_SEND, V_IR_RECEIVE
|
||||
S_WATER = 21, //!< Water meter, V_FLOW, V_VOLUME
|
||||
S_AIR_QUALITY = 22, //!< Air quality sensor, V_LEVEL
|
||||
S_CUSTOM = 23, //!< Custom sensor
|
||||
S_DUST = 24, //!< Dust sensor, V_LEVEL
|
||||
S_SCENE_CONTROLLER = 25, //!< Scene controller device, V_SCENE_ON, V_SCENE_OFF.
|
||||
S_RGB_LIGHT = 26, //!< RGB light. Send color component data using V_RGB. Also supports V_WATT
|
||||
S_RGBW_LIGHT = 27, //!< RGB light with an additional White component. Send data using V_RGBW. Also supports V_WATT
|
||||
S_COLOR_SENSOR = 28, //!< Color sensor, send color information using V_RGB
|
||||
S_HVAC = 29, //!< Thermostat/HVAC device. V_HVAC_SETPOINT_HEAT, V_HVAC_SETPOINT_COLD, V_HVAC_FLOW_STATE, V_HVAC_FLOW_MODE, V_TEMP
|
||||
S_MULTIMETER = 30, //!< Multimeter device, V_VOLTAGE, V_CURRENT, V_IMPEDANCE
|
||||
S_SPRINKLER = 31, //!< Sprinkler, V_STATUS (turn on/off), V_TRIPPED (if fire detecting device)
|
||||
S_WATER_LEAK = 32, //!< Water leak sensor, V_TRIPPED, V_ARMED
|
||||
S_SOUND = 33, //!< Sound sensor, V_TRIPPED, V_ARMED, V_LEVEL (sound level in dB)
|
||||
S_VIBRATION = 34, //!< Vibration sensor, V_TRIPPED, V_ARMED, V_LEVEL (vibration in Hz)
|
||||
S_MOISTURE = 35, //!< Moisture sensor, V_TRIPPED, V_ARMED, V_LEVEL (water content or moisture in percentage?)
|
||||
S_INFO = 36, //!< LCD text device / Simple information device on controller, V_TEXT
|
||||
S_GAS = 37, //!< Gas meter, V_FLOW, V_VOLUME
|
||||
S_GPS = 38, //!< GPS Sensor, V_POSITION
|
||||
S_WATER_QUALITY = 39 //!< V_TEMP, V_PH, V_ORP, V_EC, V_STATUS
|
||||
} mysensor_sensor;
|
||||
|
||||
/// @brief Type of sensor data (for set/req/ack messages)
|
||||
typedef enum {
|
||||
V_TEMP, // S_TEMP. Temperature S_TEMP, S_HEATER, S_HVAC
|
||||
V_HUM, // S_HUM. Humidity
|
||||
V_STATUS, // S_LIGHT, S_DIMMER, S_SPRINKLER, S_HVAC, S_HEATER. Used for setting/reporting binary (on/off) status. 1=on, 0=off
|
||||
V_LIGHT=2, // Same as V_STATUS
|
||||
V_PERCENTAGE, // S_DIMMER. Used for sending a percentage value 0-100 (%).
|
||||
V_DIMMER=3, // S_DIMMER. Same as V_PERCENTAGE.
|
||||
V_PRESSURE, // S_BARO. Atmospheric Pressure
|
||||
V_FORECAST, // S_BARO. Whether forecast. string of "stable", "sunny", "cloudy", "unstable", "thunderstorm" or "unknown"
|
||||
V_RAIN, // S_RAIN. Amount of rain
|
||||
V_RAINRATE, // S_RAIN. Rate of rain
|
||||
V_WIND, // S_WIND. Wind speed
|
||||
V_GUST, // S_WIND. Gust
|
||||
V_DIRECTION, // S_WIND. Wind direction 0-360 (degrees)
|
||||
V_UV, // S_UV. UV light level
|
||||
V_WEIGHT, // S_WEIGHT. Weight(for scales etc)
|
||||
V_DISTANCE, // S_DISTANCE. Distance
|
||||
V_IMPEDANCE, // S_MULTIMETER, S_WEIGHT. Impedance value
|
||||
V_ARMED, // S_DOOR, S_MOTION, S_SMOKE, S_SPRINKLER. Armed status of a security sensor. 1 = Armed, 0 = Bypassed
|
||||
V_TRIPPED, // S_DOOR, S_MOTION, S_SMOKE, S_SPRINKLER, S_WATER_LEAK, S_SOUND, S_VIBRATION, S_MOISTURE. Tripped status of a security sensor. 1 = Tripped, 0
|
||||
V_WATT, // S_POWER, S_LIGHT, S_DIMMER, S_RGB_LIGHT, S_RGBW_LIGHT. Watt value for power meters
|
||||
V_KWH, // S_POWER. Accumulated number of KWH for a power meter
|
||||
V_SCENE_ON, // S_SCENE_CONTROLLER. Turn on a scene
|
||||
V_SCENE_OFF, // S_SCENE_CONTROLLER. Turn of a scene
|
||||
V_HEATER, // Deprecated. Use V_HVAC_FLOW_STATE instead.
|
||||
V_HVAC_FLOW_STATE=21, // S_HEATER, S_HVAC. HVAC flow state ("Off", "HeatOn", "CoolOn", or "AutoChangeOver")
|
||||
V_HVAC_SPEED, // S_HVAC, S_HEATER. HVAC/Heater fan speed ("Min", "Normal", "Max", "Auto")
|
||||
V_LIGHT_LEVEL, // S_LIGHT_LEVEL. Uncalibrated light level. 0-100%. Use V_LEVEL for light level in lux
|
||||
V_VAR1,
|
||||
V_VAR2,
|
||||
V_VAR3,
|
||||
V_VAR4,
|
||||
V_VAR5,
|
||||
V_UP, // S_COVER. Window covering. Up
|
||||
V_DOWN, // S_COVER. Window covering. Down
|
||||
V_STOP, // S_COVER. Window covering. Stop
|
||||
V_IR_SEND, // S_IR. Send out an IR-command
|
||||
V_IR_RECEIVE, // S_IR. This message contains a received IR-command
|
||||
V_FLOW, // S_WATER. Flow of water (in meter)
|
||||
V_VOLUME, // S_WATER. Water volume
|
||||
V_LOCK_STATUS, // S_LOCK. Set or get lock status. 1=Locked, 0=Unlocked
|
||||
V_LEVEL, // S_DUST, S_AIR_QUALITY, S_SOUND (dB), S_VIBRATION (hz), S_LIGHT_LEVEL (lux)
|
||||
V_VOLTAGE, // S_MULTIMETER
|
||||
V_CURRENT, // S_MULTIMETER
|
||||
V_RGB, // S_RGB_LIGHT, S_COLOR_SENSOR.
|
||||
// Used for sending color information for multi color LED lighting or color sensors.
|
||||
// Sent as ASCII hex: RRGGBB (RR=red, GG=green, BB=blue component)
|
||||
V_RGBW, // S_RGBW_LIGHT
|
||||
// Used for sending color information to multi color LED lighting.
|
||||
// Sent as ASCII hex: RRGGBBWW (WW=white component)
|
||||
V_ID, // S_TEMP
|
||||
// Used for sending in sensors hardware ids (i.e. OneWire DS1820b).
|
||||
V_UNIT_PREFIX, // S_DUST, S_AIR_QUALITY
|
||||
// Allows sensors to send in a string representing the
|
||||
// unit prefix to be displayed in GUI, not parsed by controller! E.g. cm, m, km, inch.
|
||||
// Can be used for S_DISTANCE or gas concentration
|
||||
V_HVAC_SETPOINT_COOL, // S_HVAC. HVAC cool setpoint (Integer between 0-100)
|
||||
V_HVAC_SETPOINT_HEAT, // S_HEATER, S_HVAC. HVAC/Heater setpoint (Integer between 0-100)
|
||||
V_HVAC_FLOW_MODE, // S_HVAC. Flow mode for HVAC ("Auto", "ContinuousOn", "PeriodicOn")
|
||||
V_TEXT, // S_INFO. Text message to display on LCD or controller device
|
||||
V_CUSTOM, // Custom messages used for controller/inter node specific commands, preferably using S_CUSTOM device type.
|
||||
V_POSITION, // GPS position and altitude. Payload: latitude;longitude;altitude(m). E.g. "55.722526;13.017972;18"
|
||||
V_IR_RECORD, // Record IR codes S_IR for playback
|
||||
V_PH, // S_WATER_QUALITY, water PH
|
||||
V_ORP, // S_WATER_QUALITY, water ORP : redox potential in mV
|
||||
V_EC, // S_WATER_QUALITY, water electric conductivity μS/cm (microSiemens/cm)
|
||||
V_VAR, // S_POWER, Reactive power: volt-ampere reactive (var)
|
||||
V_VA, // S_POWER, Apparent power: volt-ampere (VA)
|
||||
V_POWER_FACTOR // S_POWER, Ratio of real power to apparent power: floating point value in the range [-1,..,1]
|
||||
V_TEMP = 0, //!< S_TEMP. Temperature S_TEMP, S_HEATER, S_HVAC
|
||||
V_HUM = 1, //!< S_HUM. Humidity
|
||||
V_STATUS = 2, //!< S_BINARY, S_DIMMER, S_SPRINKLER, S_HVAC, S_HEATER. Used for setting/reporting binary (on/off) status. 1=on, 0=off
|
||||
V_LIGHT = 2, //!< \deprecated Same as V_STATUS, **** DEPRECATED, DO NOT USE ****
|
||||
V_PERCENTAGE = 3, //!< S_DIMMER. Used for sending a percentage value 0-100 (%).
|
||||
V_DIMMER = 3, //!< \deprecated Same as V_PERCENTAGE, **** DEPRECATED, DO NOT USE ****
|
||||
V_PRESSURE = 4, //!< S_BARO. Atmospheric Pressure
|
||||
V_FORECAST = 5, //!< S_BARO. Whether forecast. string of "stable", "sunny", "cloudy", "unstable", "thunderstorm" or "unknown"
|
||||
V_RAIN = 6, //!< S_RAIN. Amount of rain
|
||||
V_RAINRATE = 7, //!< S_RAIN. Rate of rain
|
||||
V_WIND = 8, //!< S_WIND. Wind speed
|
||||
V_GUST = 9, //!< S_WIND. Gust
|
||||
V_DIRECTION = 10, //!< S_WIND. Wind direction 0-360 (degrees)
|
||||
V_UV = 11, //!< S_UV. UV light level
|
||||
V_WEIGHT = 12, //!< S_WEIGHT. Weight(for scales etc)
|
||||
V_DISTANCE = 13, //!< S_DISTANCE. Distance
|
||||
V_IMPEDANCE = 14, //!< S_MULTIMETER, S_WEIGHT. Impedance value
|
||||
V_ARMED = 15, //!< S_DOOR, S_MOTION, S_SMOKE, S_SPRINKLER. Armed status of a security sensor. 1 = Armed, 0 = Bypassed
|
||||
V_TRIPPED = 16, //!< S_DOOR, S_MOTION, S_SMOKE, S_SPRINKLER, S_WATER_LEAK, S_SOUND, S_VIBRATION, S_MOISTURE. Tripped status of a security sensor. 1 = Tripped, 0
|
||||
V_WATT = 17, //!< S_POWER, S_BINARY, S_DIMMER, S_RGB_LIGHT, S_RGBW_LIGHT. Watt value for power meters
|
||||
V_KWH = 18, //!< S_POWER. Accumulated number of KWH for a power meter
|
||||
V_SCENE_ON = 19, //!< S_SCENE_CONTROLLER. Turn on a scene
|
||||
V_SCENE_OFF = 20, //!< S_SCENE_CONTROLLER. Turn of a scene
|
||||
V_HVAC_FLOW_STATE = 21, //!< S_HEATER, S_HVAC. HVAC flow state ("Off", "HeatOn", "CoolOn", or "AutoChangeOver")
|
||||
V_HEATER = 21, //!< \deprecated Same as V_HVAC_FLOW_STATE, **** DEPRECATED, DO NOT USE ****
|
||||
V_HVAC_SPEED = 22, //!< S_HVAC, S_HEATER. HVAC/Heater fan speed ("Min", "Normal", "Max", "Auto")
|
||||
V_LIGHT_LEVEL = 23, //!< S_LIGHT_LEVEL. Uncalibrated light level. 0-100%. Use V_LEVEL for light level in lux
|
||||
V_VAR1 = 24, //!< VAR1
|
||||
V_VAR2 = 25, //!< VAR2
|
||||
V_VAR3 = 26, //!< VAR3
|
||||
V_VAR4 = 27, //!< VAR4
|
||||
V_VAR5 = 28, //!< VAR5
|
||||
V_UP = 29, //!< S_COVER. Window covering. Up
|
||||
V_DOWN = 30, //!< S_COVER. Window covering. Down
|
||||
V_STOP = 31, //!< S_COVER. Window covering. Stop
|
||||
V_IR_SEND = 32, //!< S_IR. Send out an IR-command
|
||||
V_IR_RECEIVE = 33, //!< S_IR. This message contains a received IR-command
|
||||
V_FLOW = 34, //!< S_WATER. Flow of water (in meter)
|
||||
V_VOLUME = 35, //!< S_WATER. Water volume
|
||||
V_LOCK_STATUS = 36, //!< S_LOCK. Set or get lock status. 1=Locked, 0=Unlocked
|
||||
V_LEVEL = 37, //!< S_DUST, S_AIR_QUALITY, S_SOUND (dB), S_VIBRATION (hz), S_LIGHT_LEVEL (lux)
|
||||
V_VOLTAGE = 38, //!< S_MULTIMETER
|
||||
V_CURRENT = 39, //!< S_MULTIMETER
|
||||
V_RGB = 40, //!< S_RGB_LIGHT, S_COLOR_SENSOR. Sent as ASCII hex: RRGGBB (RR=red, GG=green, BB=blue component)
|
||||
V_RGBW = 41, //!< S_RGBW_LIGHT. Sent as ASCII hex: RRGGBBWW (WW=white component)
|
||||
V_ID = 42, //!< Used for sending in sensors hardware ids (i.e. OneWire DS1820b).
|
||||
V_UNIT_PREFIX = 43, //!< Allows sensors to send in a string representing the unit prefix to be displayed in GUI, not parsed by controller! E.g. cm, m, km, inch.
|
||||
V_HVAC_SETPOINT_COOL = 44, //!< S_HVAC. HVAC cool setpoint (Integer between 0-100)
|
||||
V_HVAC_SETPOINT_HEAT = 45, //!< S_HEATER, S_HVAC. HVAC/Heater setpoint (Integer between 0-100)
|
||||
V_HVAC_FLOW_MODE = 46, //!< S_HVAC. Flow mode for HVAC ("Auto", "ContinuousOn", "PeriodicOn")
|
||||
V_TEXT = 47, //!< S_INFO. Text message to display on LCD or controller device
|
||||
V_CUSTOM = 48, //!< Custom messages used for controller/inter node specific commands, preferably using S_CUSTOM device type.
|
||||
V_POSITION = 49, //!< GPS position and altitude. Payload: latitude;longitude;altitude(m). E.g. "55.722526;13.017972;18"
|
||||
V_IR_RECORD = 50, //!< Record IR codes S_IR for playback
|
||||
V_PH = 51, //!< S_WATER_QUALITY, water PH
|
||||
V_ORP = 52, //!< S_WATER_QUALITY, water ORP : redox potential in mV
|
||||
V_EC = 53, //!< S_WATER_QUALITY, water electric conductivity μS/cm (microSiemens/cm)
|
||||
V_VAR = 54, //!< S_POWER, Reactive power: volt-ampere reactive (var)
|
||||
V_VA = 55, //!< S_POWER, Apparent power: volt-ampere (VA)
|
||||
V_POWER_FACTOR = 56, //!< S_POWER, Ratio of real power to apparent power: floating point value in the range [-1,..,1]
|
||||
} mysensor_data;
|
||||
|
||||
|
||||
/// @brief Type of internal messages (for internal messages)
|
||||
typedef enum {
|
||||
I_BATTERY_LEVEL,
|
||||
I_TIME,
|
||||
I_VERSION,
|
||||
I_ID_REQUEST,
|
||||
I_ID_RESPONSE,
|
||||
I_INCLUSION_MODE,
|
||||
I_CONFIG,
|
||||
I_FIND_PARENT,
|
||||
I_FIND_PARENT_RESPONSE,
|
||||
I_LOG_MESSAGE,
|
||||
I_CHILDREN,
|
||||
I_SKETCH_NAME,
|
||||
I_SKETCH_VERSION,
|
||||
I_REBOOT,
|
||||
I_GATEWAY_READY,
|
||||
I_SIGNING_PRESENTATION, //!< Provides signing related preferences (first byte is preference version)
|
||||
I_NONCE_REQUEST, //!< Request for a nonce
|
||||
I_NONCE_RESPONSE, //!< Payload is nonce data
|
||||
I_HEARTBEAT,
|
||||
I_PRESENTATION,
|
||||
I_DISCOVER,
|
||||
I_DISCOVER_RESPONSE,
|
||||
I_HEARTBEAT_RESPONSE,
|
||||
I_LOCKED, //!< Node is locked (reason in string-payload)
|
||||
I_PING, //!< ping sent to node, payload incremental hop counter
|
||||
I_PONG, //!< in return to ping, sent back to sender, payload incremental hop counter
|
||||
I_REGISTER_REQUEST, //!< register request to GW
|
||||
I_REGISTER_RESPONSE, //!< register response from GW
|
||||
I_DEBUG //!< debug message
|
||||
|
||||
I_BATTERY_LEVEL = 0, //!< Battery level
|
||||
I_TIME = 1, //!< Time
|
||||
I_VERSION = 2, //!< Version
|
||||
I_ID_REQUEST = 3, //!< ID request
|
||||
I_ID_RESPONSE = 4, //!< ID response
|
||||
I_INCLUSION_MODE = 5, //!< Inclusion mode
|
||||
I_CONFIG = 6, //!< Config
|
||||
I_FIND_PARENT = 7, //!< Find parent
|
||||
I_FIND_PARENT_RESPONSE = 8, //!< Find parent response
|
||||
I_LOG_MESSAGE = 9, //!< Log message
|
||||
I_CHILDREN = 10, //!< Children
|
||||
I_SKETCH_NAME = 11, //!< Sketch name
|
||||
I_SKETCH_VERSION = 12, //!< Sketch version
|
||||
I_REBOOT = 13, //!< Reboot request
|
||||
I_GATEWAY_READY = 14, //!< Gateway ready
|
||||
I_SIGNING_PRESENTATION = 15, //!< Provides signing related preferences (first byte is preference version)
|
||||
I_NONCE_REQUEST = 16, //!< Request for a nonce
|
||||
I_NONCE_RESPONSE = 17, //!< Payload is nonce data
|
||||
I_HEARTBEAT = 18, //!< Heartbeat request
|
||||
I_PRESENTATION = 19, //!< Presentation message
|
||||
I_DISCOVER = 20, //!< Discover request
|
||||
I_DISCOVER_RESPONSE = 21, //!< Discover response
|
||||
I_HEARTBEAT_RESPONSE = 22, //!< Heartbeat response
|
||||
I_LOCKED = 23, //!< Node is locked (reason in string-payload)
|
||||
I_PING = 24, //!< Ping sent to node, payload incremental hop counter
|
||||
I_PONG = 25, //!< In return to ping, sent back to sender, payload incremental hop counter
|
||||
I_REGISTER_REQUEST = 26, //!< Register request to GW
|
||||
I_REGISTER_RESPONSE = 27, //!< Register response from GW
|
||||
I_DEBUG = 28 //!< Debug message
|
||||
} mysensor_internal;
|
||||
|
||||
|
||||
/// @brief Type of data stream (for streamed message)
|
||||
typedef enum {
|
||||
ST_FIRMWARE_CONFIG_REQUEST,
|
||||
ST_FIRMWARE_CONFIG_RESPONSE,
|
||||
ST_FIRMWARE_REQUEST,
|
||||
ST_FIRMWARE_RESPONSE,
|
||||
ST_SOUND,
|
||||
ST_IMAGE
|
||||
ST_FIRMWARE_CONFIG_REQUEST = 0, //!< Request new FW, payload contains current FW details
|
||||
ST_FIRMWARE_CONFIG_RESPONSE = 1, //!< New FW details to initiate OTA FW update
|
||||
ST_FIRMWARE_REQUEST = 2, //!< Request FW block
|
||||
ST_FIRMWARE_RESPONSE = 3, //!< Response FW block
|
||||
ST_SOUND = 4, //!< Sound
|
||||
ST_IMAGE = 5 //!< Image
|
||||
} mysensor_stream;
|
||||
|
||||
/// @brief Type of payload
|
||||
typedef enum {
|
||||
P_STRING,
|
||||
P_BYTE,
|
||||
P_INT16,
|
||||
P_UINT16,
|
||||
P_LONG32,
|
||||
P_ULONG32,
|
||||
P_CUSTOM,
|
||||
P_FLOAT32
|
||||
P_STRING = 0, //!< Payload type is string
|
||||
P_BYTE = 1, //!< Payload type is byte
|
||||
P_INT16 = 2, //!< Payload type is INT16
|
||||
P_UINT16 = 3, //!< Payload type is UINT16
|
||||
P_LONG32 = 4, //!< Payload type is INT32
|
||||
P_ULONG32 = 5, //!< Payload type is UINT32
|
||||
P_CUSTOM = 6, //!< Payload type is binary
|
||||
P_FLOAT32 = 7 //!< Payload type is float32
|
||||
} mysensor_payload;
|
||||
|
||||
|
||||
|
||||
Reference in New Issue
Block a user