* Added support for I2C EEPROM OTA
* EEPROM OTA now uses extEEPROM as driver
* Compiler warning fix
* Style check fixes
* Fix doxygen warnings of I2CEeprom
* Use bool instead of boolean in I2CEeprom shim
* Fix re-merged style problem
* Signing support with MAX_PAYLOAD>32
Support in the signing backends to handle configurations
where MAX_PAYLOAD is more than 32 bytes.
Fixes#748
* Support big message signatures
Support for signing messages larger than 32 bytes.
This is not fully testable with the current version of
the library but the change would add theoretical support
for signing any sized messages.
Fixes#749
* Have gw properly indicate whitelisting preferences
If the gateway hold a signing whitelist, inform all
nodes of this requirement and not just nodes that hold
whitelists themselves.
Fixes#806
* Harden security
The flag MY_SIGNING_GW_REQUEST_SIGNATURES_FROM_ALL
has been removed. Gateway will now request signatures
from everyone by default.
In addition to this, no nodes in the network will allow
clearing of signing/whitelisting preferences by OTA
commands by default.
If the old behaviour is needed (suitable for gradual
signing roll out and development purposes) a new flag,
MY_SIGNING_WEAK_SECURITY can be set.
Fixes#807
* Signing debug messages rewritten
All signing related debug has been rewritten to
better match other core debug printouts.
Also, backends are updated to have a smaller
implementation delta.
* Simplified signing option implemented
Enable by MY_SIGNING_SIMPLE_PASSWD. Signing, and signing requirements
will be enabled, as will encryption. Whitelisting is optional.
The value provided to MY_SIGNING_SIMPLE_PASSWD is used as HMAC and AES
key. Whitelists use the first 8 bytes of the password and the ninth
byte from the node ID as serial.
Password is required to be at least 8 characters wide. It is zero
padded if it is not long enough to cover the AES (16 bytes) and HMAC
(32 bytes) keys. It is not recommended to have a password shorter than
32 bytes, and there is no need for a password longer than 32 bytes.
* Add documentation section for signing debug
* Add nRF5 encryption to simple signing option
* Restructure MySigning documentation
* Minor fixes for Linux
* Add NVRAM support
This is an EEPROM replacement based on MCU's internal Flash memory.
The NVRAM class is designed to be stateless. Each operation is
written to flash immediately.
The last 16k(nRF51)/32k(nRF52) of Flash memory are managed by the
VirtualPage class. This class allows writing a single emulated 4k
page up 40,000 times.
The NVRAM class is a log based byte-wise storage allowing up to
40,000,000 writes depending on the number of used addresses. Each
four allocated addresses from the beginning of the NVRAM reduce the
write log by one.
When first 256 bytes of the emulated storage are used, there is an
average writing capacity of 145,000 cycles per byte.
When the write log is full, the NVRAM is compressed into a new flash
page. After a new page is ready, the old page is released. This
process can take up to 4500 ms and cannot be interrupted.
The NVRAM functionality can easily be ported to ESP8266 or SAMD by
providing a Flash interface.
* Add NRF5 platform support
This is the support of the Nordic Semiconductor NRF51 (nrf51822,
nrf51422) and NRF52 (nrf52832) platform. Based on arduino-nRF5
(https://github.com/sandeepmistry/arduino-nRF5).
The included radio driver is compatible with the NRF24 devices.
Using a SoftDevice (BLE)is not supported and must be removed before
flashing MySensors with a "mass_erase" operation.
RPi and Linux refactor.
Add GPIO Sysfs for GPIO operations.
Update configure script.
Fix some cppcheck warnings.
Add serial emulation that prints to stdout.
Fix some file headers.
* Add .astylerc with the core coding standard
* Added pre-commit git hook
The hook currently only checks code format using
astyle and will not permit commits which cause
astyle to change the contents of any source file
in the commit.
This is useful to have automatic coding standard
verification done without having to wait for
Jenkins to react to a pull request.
Installation:
Linux:
ln -s ../../tools/hooks/pre-commit.sh .git/hooks/pre-commit
Windows:
copy tools\hooks\pre-commit.sh .git\hooks\pre-commit
* Added editorconfig and updated gitattributes
Unix style line endings are now default.
* Resolved doxygen warning
Removing MY_LED_BLINKING_FEATURE, as we now are
using MY_DEFAULT_LED_xx_PIN defines to enable
LED blinking feature.
updated Gateway sketches to not refer to
MY_LED_BLINKING_FEATURE any more
fixes#562
d00616
Patrick Fallberg
Olivier
Krister W
Marcelo Aquino
Dustin
tekka007
Olivier
Henrik Ekblad
Marcelo Aquino
Thomas Mørch